Home > Error Code > Tranax Atm Error Codes

Tranax Atm Error Codes

Contents

D2200 EOT not received from host Verify all programming. Inspect all cables for possible damage. Check vault door switch. It the status clears, place the cash dispenser in service. http://u2commerce.com/error-code/tranax-error-codes.html

Recommended Action: See the recommended action for error code 144. Otherwise the dispenser may require service C004B Long note detected 3 times consecutively Verify the quality of the cash. Clean dispenser. Error Code: 130 Description: Command not acknowledged by the dispenser mechanism. http://www.atmdepot.com/tranax-atm-error-codes/

Hantle 1700w Error Codes

Outside interference may cause it (neon signs, lights).CDN11No Response after 3 retry of commandCDN12No Response between ENQ-ACK after 5 retry of ENQCDN13No Response after 5 retry because of timeout between STX-BCC D0052 No checking account Code reported by host processor. Results: No money is dispensed, screen and receipt display system unavailable. Recommended Action: Inspect the feed path exit sensor for jammed documents and broken components.

You may also want to try the reset button on the printer to clear this error. If error is persistent the dispenser may require service. Code reported by host processor. Atm Error Codes Hyosung Error Code: 321(45h)[E] Description: Cassette data corrupted.

Otherwise the dispenser may require service C0030 CDU motor failure Motor speed (measured at the encoder wheel) was not within spec. Tranax 1700 Error Codes Specific meaning or definition can vary between the different processors. Reinitialize CDU C0083 Stacker sensor failure Check all wiring connections to CDU mainboard. http://www.propointcs.com/index.php/tranax/Page-11.html This error is of concern only if it is repeated.

If error persists, replace the SPED keypad module. Atm Error Code D2516 Verify that version of Mini-Bank Software matches host processor. Recommended Action: This error code is generated when there is a checksum error in data stored in the note cassette. Home | | About Us | | Equipment & Supplies | | Support Center | | Contact Us | | Company News | | Testimonials | | Pay Your Invoice... 877-306-1506

  • Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.
  • This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode).D1706Modem connection errorPhone line connected to ATM will not support data communication.
  • Paper of a lesser thickness is more prone to jamming. 20012 Receipt printer feed lever open Close the feed tray on the printer.
  • This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode).

Tranax 1700 Error Codes

Error Code: 195 Description: Receipt printer out of paper. useful reference Recommended Action: See the recommended action for error code 144. Hantle 1700w Error Codes If cash dispenser operates normally, it will pick from seven to fifteen notes from each cassette to calibrate the double detect to the document in each of the cassettes. Genmega Error Codes Purge the dispenser using the purge command.

Check with Triton Systems Technical Support for known software incompatibilities. navigate here Make sure all connectors attached to the CMC are seated in their receptacles. Otherwise, put the cash dispenser into service. Error Code: 192 Description: Communications error. Atm Error D1706

CDN0F CDU connection failure Check cables between CDU and Mainboard, remove cables (even though they may be attached) and re-connect. The dispenser and mainboard are programmed with a country code (USA or Canada). Excessive EMI emissions from outside source (neon sign, freezer)are likely causes. Check This Out C004E Miscount of notes between sensors Test CDU using diagnostics, use journal to verify amount of dispensed notes versus requested notes.

Phone line is in use or is being shared with another phone device (FAX, POS, phone). Hantle 1700w Troubleshooting Use an electrical parts contact cleaner to clean the terminals. Restart the cash dispenser.

Error Code: 3 Description: BCD NOANSWER Possible Cause: Possible may be a processor or telephone hardware problem.

Ensure that each cable is securely fastened to its termination point. Restart the cash dispenser and reset the error. Contact host processorD2500Cannot connect to the hostCheck the connectionD2510Timeout while SendingD2511Communication error while SendingD2513Timeout while ReceivingD2514Communication error while ReceivingD2515Socket Error while ReceivingD3203Modem Initialization ErrorReseat socket modem, then replace modemD3204Invalid Host phone Triton Error Codes Replace Mainboard W0001 WebRMS failed to dial into the ATM This does not mean that the ATM is down; it’s a warning message that WebRMS could not dial into the ATM

Possible Cause: A corrupt pin-working key may cause this problem. It usually occurs when attempting to dispense documents that are unacceptable or documents that have not been prepared properly. 1. Excessive EMI emissions from outside source (neon sign, freezer). this contact form Error Code: 146 Description: No reply from command to electronic journal.