Home > Error Code > Tranax Error Code

Tranax Error Code

Contents

Test the dispensing mechanism by completing several test dispenses. 4. Error Code: 49 (31h) Description: Jam at exit Recommended Action: This status is generated when exit sensor is blocked. 1. This will reset the reject event counters. That's a 10% monthly return!  Now, imagine your ATM is in a busy location where 10 people per day use it!  Now imagine you have 5 or 10 machines in just http://u2commerce.com/error-code/tranax-error-code-565.html

Remove the cassette and visually inspect for loose or disconnected connectors on both the upper and lower width sensor printed circuit boards. 3. Check and reseat all belts. Error Code: 129 Description: No response from the dispenser mechanism. Make sure it is seated at the main board at J15 and at the printer control board at CN6. http://www.atmdepot.com/tranax-atm-error-codes/

Hantle 1700w Error Codes

This error code will cause the cash dispenser to go "Out of Service". If persistent, clean and test the card reader in diagnostics. Verify that the SPED board has the correct DC voltages applied to it. Inspect the reject vault present sensor visually for proper operation.

  • If at any time during the following checks, the ""faulty note qualifier"" error code recurs.
  • In most cases you may have to remove the printer to locate difficult jams.
  • If these actions have no effect on dispenser operation, replace the dispenser mechanism and/or the note cassette.
  • Recommended Action: This Error Code is valid for units with SPED keypad device installed.
  • Use an electrical parts contact cleaner to clean the terminals.

Error Code: 52 (34h) Description: RAM error Recommended Action: A mechanical failure has occurred. Verify that version of Mini-Bank Software matches host processor. Error Code: 142 Description: Dispenser returns bad command error. Atm Error Codes Hyosung broken belts, broken gears, disconnected or damaged cables, broken timing wheel etc.).

In line filter may fix this. Reset the error code. Reset the cash dispenser. Generated Sun, 30 Oct 2016 17:39:22 GMT by s_hp90 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection

This is normally an internal terminal problem. Atm Error Code D2516 PURGE the dispensing mechanism. The system returned: (22) Invalid argument The remote host or network may be down. Inspect the cable supplying DC power from the power supply to the printer.

Tranax 1700 Error Codes

The paper low sensor may be dirty and require cleaning. Replace Mainboard W0001 WebRMS failed to dial into the ATM This does not mean that the ATM is down; it’s a warning message that WebRMS could not dial into the ATM Hantle 1700w Error Codes Check and reseat all belts. Genmega Error Codes Specific meaning or definition can vary between the different processors.

Restart the operating system. http://u2commerce.com/error-code/tranax-error-codes.html Specific meaning or definition can vary between the different processors. Purge the dispenser using the purge command. D0092 System unavailable Code reported by host processor. Atm Error D1706

W0003 WebRMS could not retrieve the local ATM time Although webRMS successfully retrieved the journal information, it could not find the ATM’s local time. (This is equivalent to the “-1/-1/-001″ error Error Code: 166 Description: Bad dispense. CDN05 CDU connection failure Check cables between CDU and Mainboard, remove cables (even though they may be attached) and re-connect. http://u2commerce.com/error-code/tranax-20013-error-code.html Verify that version of Mini-Bank Software matches host processor.

Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Hantle 1700w Troubleshooting Ensure that each cable is securely fastened to its termination point. Error Code: 106 (6Ah) Description: FIFO error Recommended Action: The dispensing mechanism may have corrupt software.

Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error.

Complete several test dispenses. Inspect the note diverter in the note transport module. If the error does not show again put the cash dispenser back into service. Triton Error Codes It will also be stored as part of the transaction data in the electronic journal.

Error Code: 51 (33h) Description: Accountancy error Recommended Action: A mechanical failure has occurred. If these actions have no effect, replace the dispenser. Recommended Action: See the recommended action for error code 144. navigate here Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON.

Use the diagnostic functions or NMD test software to determine if a note feeder has a faulty or dirty sensor. Verify that all sensors are operation correctly. Verify that version of Mini-Bank Software matches host processor. Recommended Action: See the recommended action for error code 128 Error Code: 134 Description: Exit blocked as reported by error code check.

Replace the exit sensor if defective. If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). Contact host processor D00A6 FS omitted (after total non cash dispense amount in day close) Verify all programming.