Home > Error Code > Tranax Error Codes

Tranax Error Codes


Make sure that the cassettes are installed and locked before performing a test dispense or live transaction. Clear terminal error code. Test the dispenser by completing several test dispenses with the test dispense command. Paper of a lesser thickness is more prone to jamming. 20012 Receipt printer feed lever open Close the feed tray on the printer. Source

Inspect the feed path for jammed currency. Error Code: 301(31h)[1] Description: Low level in cassette. Use an electrical parts contact cleaner on terminals. Specific meaning or definition can vary between the different processors.

Hantle 1700w Error Codes

Complete several test dispenses. D0050 Transaction is not approved Code reported by host processor (Shazam). D0019 Reenter the entire transaction Code reported by host processor (Shazam).

Reinitialize CDU. Recommended Action: This status occurs when a note arrives at the double detect without being seen by the feed sensor. 1. Error Code: 190 Description: Pin Master key not configured. Atm Error Codes Hyosung Clean the sensors a needed. 3.

If the problem persists, replace the dispensing mechanism. Tranax 1700 Error Codes C0048 Incorrect bill count Verify cash count in the Settlement menu. If the power supply if operating normally, replace the note qualifier to correct the problem. http://atmequipment.com/s.nl/it.I/id.17/.f Inspect the note qualifier and note transport for broken components (i.e.

Error Code: 136 Description: Modem initialization failed. Atm Error Code D2516 Then it will complete the test dispense function. If the error code is reported again, it may be necessary to replace the CMC or one of the note feeder controllers. Error Code: 353(65h)[e] Description: No message to resend.

Tranax 1700 Error Codes

Recommended Action: This error code is generated when the LIFTS UP command fails to open a note cassette to the operating position. Recommended Action: This error code is generated when there is a sensor error in one or more of the note feeders or when there is a document jammed in the note Hantle 1700w Error Codes If error is persistent, modem may be defective. Genmega Error Codes If this error is consistent, the printer or mainboard may require service.

Check the operation of all sensors in the note transport module. this contact form Click to Contact us or call 888-959-2269 Article Archives August 2016 June 2016 January 2016 March 2015 February 2015 November 2014 October 2014 May 2014 January 2014 November 2013 October 2013 Check wiring to mainboard.C00E1NS4 darkVerify connections to NS4 sensor. Complete a live transaction. Atm Error D1706

  • Your cache administrator is webmaster.
  • Error Code: 5 Description: Connect 1200 Baud then lost carrier or connection.
  • Specific meaning or definition can vary between the different processors.

LEARN MORE ATM Merchant Systems’ customized ATM programs meet your needs and exceed your expectations. Excessive EMI emissions from outside source (neon sign, freezer)are likely causes. Open the Printer Bracket and verify that there are no jams in the printer or the paper path. have a peek here Test the dispenser by completing several test dispenses. 4.

Company News . . Hantle 1700w Troubleshooting Make sure the note diverter moves freely. Error Code: 128 Description: Error in reply from the dispenser mechanism Recommended Action: 1.

Clear all errors and test the dispenser by completing several TEST DISPENSES.

This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode). D2100 Modem initialization error Check modem in diagnostics or modem test. W0004 The ATM time, as set in the Operator Function Menu, is incorrect WebRMS has detected that the ATM probably has incorrect date and time settings. Triton Error Codes Check with the processor.

It the status clears, place the cash dispenser in service. Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Contact host processor D00A8 FS omitted (after surcharge amount in configuration message) Verify all programming. Check This Out Check to make sure that cables connecting the note transport and the CMC module are not damaged.

Services & Support Financial Services Professional Services Transaction Processing Value Added Services Real Time Reporting Client Support Contact Info ATM Merchant Systems ATMMS Financial Products 1667 Helm Drive Las Vegas, NV Clear the error. 5. C005E Dispense command size check error Re-initialize machine, verify connections to mainboard. Test the dispenser by completing several test dispenses. 4.

Make sure the tamper screw is secure to the SPED module. Reset the error code.