Home > Error Code > Triton 8100 Error Codes

Triton 8100 Error Codes

Contents

If the problem persists; replace the dispenser. 49 (31h) Jam at exit Inspect the feed path for jammed notes. Enter the management functions and attempt to complete the print journal command. If the voltages are not within tolerance, the cable or power supply may be defective. 4. Once you have completed one of the above(more…) 152 Electronic journal corrupt 1. this contact form

If no jam is located, remove the first note from the cassette. Reset the error. If the error clears; put the cash dispenser in service. 4. Time-out is typically 60 seconds. 3. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Atm Error Code 148

If the problem persists, replace the dispensing mechanism. 136 Modem initialization failed 1. Clear terminal error code. This is a Triton Connect error. Purge the dispenser with the purge command under diagnostics.

  1. Make sure they are seated at the printer control board and not damaged. 6.
  2. Replace the dispenser is the error persists. 360 Dispenser invalid return ID.
  3. Purge the dispenser using the purge command.
  4. Seat connectors or replace the power supply as needed. 2.

Inspect the incoming power and check for proper grounding 51 (33h) Suspect exit accountancy A mechanical failure has occurred. Inspect for jammed currency at the Exit. Replace the power supply or dispenser DC power if either is defective.3. Triton Atm Error Code 101 If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main

Clean the exit sensor using a soft brush and a vacuum cleaner. Triton Error Code 244 Instead, save the journal to an external USB storage device or download to Triton Connect. Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. http://www.atmnetwork.net/support/troubleshooting/Triton8100.asp Clean the width sensor with compressed air.

Other components that may cause this error are the main board or the dispensing mechanism; If the problem persists; replace the dispenser and or the main board. 129 No response from Triton Traverse Error Code 917 Inspect the note transport make sure all belts are on track and there is no currency jammed in the transport or exit areas. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 122 Unexpected note at exit 1. Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON.

Triton Error Code 244

The cash dispenser will only be placed ìOut of Serviceî when all cassettes are empty. other Refer to error code 535. 546 Card Reader ñ No data. Triton Atm Error Code 148 If EOT is received on subsequent attempts; then Error Code 1 is reported. (If problem persists call Your Service Provider or Triton Tech Support). 15 Timed out waiting for EOT See Triton Error Code 151 Inspect the printer data cable for damage.

Make sure that all cables are securely fastened to their termination points. http://u2commerce.com/error-code/triton-error-codes-135.html Suspect the ATM power supply, incoming power, the dispenser software or the main board / CPU. 239 SPED serial number change The serial number stored in the software does not match Inspect the note diverter in the note transport module. Inspect the currency for excessive wear. Atm Error Codes List

If the error clears, put the ATM in service. 5. Clear the error. Complete several test dispenses. navigate here Test the dispenser by completing several test dispenses. 5.

Reset the cash dispenser. Mitsubishi Triton Error Codes Retry the test operation and request fifty or fewer notes. 319(43h)[C] Jam in note transport. Make sure they are seated at the printer control board and not damaged. 6.

The feed sensors may be dirty.

Inspect electronic journal to dispenser communication cable for damage. Sales: 1.800.929.0228 SERVICES FOR: Shop Our Online Store EMAIL SALES EMAIL SERVICE About About Us Why Choose Us Products Overview Online Store ATMs Signage Parts Paper Upgrades Special Offers Services Remove any unacceptable currency from the cassette. 2. Triton 9100 Error Code 148 Clear any jammed currency. 2.

If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly. 3. Install a new roll of paper if needed. 2. Inspect the note diverter for proper operation and damage. his comment is here Place all belts on their rollers and gears.

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 125 Initial status check failed 1. Remove jammed currency. 2. Replace the dispensing mechanism. 54 Operation time-out 1. Clear all errors and test the dispenser by completing several TEST DISPENSES.

This error is produced when a sensor in note transport module is not working correctly during an internal self-test preceding the movement commands. Then it will complete the test dispense function. Generated Mon, 31 Oct 2016 02:03:18 GMT by s_fl369 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Inspect the note feeders and note qualifier for damage.

If the cables are undamaged, the main board or electronic journal may be defective 160 Electronic journal set featured failed 1. Find the first occurrence of “116”. Check with Triton Systems Technical Support for known software incompatibilities. 332(50h)[P] Cassettes may have been changed. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.

If all sensors are operation correctly; and the error persists; replace the replace the dispenser. 42 (2Ah) Transport Error This is a timing wheel or timing wheel sensor error. 1. Clear terminal error code. Program the cassette by injecting a new cassette ID into the cassette. If error persists; replace the SPED module. 565 Cabinet door open.

Reset the cash dispenser. Reload cassettes. See Recommended Actions for Error Code 134 136 Modem initialization failed Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. If any sensor is out of its calibration limits; clean all of the sensors and attempt to do a transaction.

Verify the blue lever on the left side of the printer in the print position. 3. Inspect main board to electronic journal communication cable for damage.