Home > Error Code > Triton 9100 Atm Error Codes

Triton 9100 Atm Error Codes

Contents

If the error clears; put the cash dispenser in service. 4. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 2. If error persists; replace the dispenser mechanism. 377 Dispenser device error. Fill if needed. http://u2commerce.com/error-code/triton-9100-error-codes.html

Clear terminal error code. Replace the dispenser is the error persists. 368 Dispenser cannot dispense the request. Purge the dispenser using the purge command. It may be necessary to replace the dispenser. 201 Dispenser detected more than six errors in a dispense This status is generated when there are 6 rejects during the current dispense. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Error Code 244

Probable cause for this error is a faulty or uncalibrated double detect module, or a jammed currency in the double detect.1. Make sure that the exit sensor is clean and operation correctly.3. Complete several test dispenses. Modem may be defective. (If problem persists call Your Service Provider or Triton Tech Support) 6 BGD_NODIALTONE No money is dispensed; screen and receipt display system unavailable. 1.

Refer to error 500. 513 SPED device offline. If the error persists; replace the dispenser. 46 (2Eh) Exit quantified A mechanical failure has occurred. This may be due to jammed documents in the transport path between the note qualifier and the note diverter. Triton Error Code 139 If the cable appears to be in acceptable condition; verify that the voltages at PL2 on the back of the dispenser are correct.

Purge the dispensing mechanism with the PURGE command from the DIAGNOSTICS function. Triton Error Code 151 Refer to error code 535. 544 Card Reader ñ Invalid request. Clear any jammed currency. 2. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php Make sure all connectors attached to the CMC are seated in their receptacles.

Inspect the card reader assembly. Triton 9100 Error Code 148 Make sure the battery is seated secure in the battery holder. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5 If the cables are undamaged Verify that the dispenser mechanism has data and power cable connected.

Triton Error Code 151

If the problem persists; replace the CPU Module. 143 PTDF error This error code will occur only in cash dispensers running ACS terminal software. Release the Printer Locking screw. Triton Error Code 244 Inspect electronic journal to dispenser communication cable for damage. Atm Error Codes List Inspect main board to electronic journal communication cable for damage.

Inspect the cassette and feed path for currency that is stuck together or jammed. 3. weblink Refer to error 500. 514 SPED device bit stuck. New ATM Machines Nautilus (Hyosung) Triton Hantle Genmega Used ATM Machines Nautilus (Hyosung) Triton Hantle Genmega ATM Parts Nautilus (Hyosung) Triton Hantle Genmega POS Equipment Verifone Hypercom Momentum Nurit ATM Paper Release the printer locking screw. Mitsubishi Triton Error Codes

Install a new roll of paper if needed. 2. Verify that all DC voltages applied to the printer control board are correct. When the note is stuck in between the note transport sensor and the throat. navigate here If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly 5.

Examples of this are two move commands sent one after another or a deliver command that is sent without a previous move command. Triton Atm Error Code 101 Program the cassette by injecting a new cassette ID into the cassette. Make sure all ports on your gateway (connecting router) are open for bidirectional comms. 3.

If the currency is in ìîfitîî condition and the error condition persists; consider replacing the note cassette or the dispensing mechanism. 102 (66h) Error (Pick Motor over current) 1.

  1. If the cables are undamaged, the main board or electronic journal may be defective 153 Electronic journal mode 1.
  2. Inspect the cassette and feed path for jammed notes.
  3. Reset error code code.
  4. This status is reported if the exit sensor is covered for a longer that allowed time for the current notes.1 Inspect the note transport and delivery throat make sure all belts
  5. Inspect for jammed currency in the transport path between the width sensors and the reject sensor.
  6. If the error code persists; replace the note transport module. 343(5Bh)[[] Sensor error or sensor covered.
  7. Make sure the shelf that the dispenser is mounted on is level and seated at all four corners. 3 Make sure the diverter moves freely. 4.
  8. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.
  9. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.
  10. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.

This error code is generated when the number of reject events exceeds 37 events. If the error code is repeated; replace the note feeder or note feeder controller for the affected feed channel. 353(65h)[e] No message to resend. Change baud rate settings. 4. Triton Error Code 246 Make sure that cable is connected at both ends.

b. Test the dispenser by completing several test dispenses with the test dispense command. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 104 Unable to clear width sensor. http://u2commerce.com/error-code/triton-atm-9100-error-codes.html Find the first occurrence of “116”.

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 122 Unexpected note at exit 1. The cash dispenser may be turned OFF; or the telephone line is shared with some other device that connects to the line before the cash dispenser. Clear the error. If the cash dispenser operates normally while performing a test dispense; put it back into service.