Home > Error Code > Triton 9100 Error 134

Triton 9100 Error 134

Contents

Inspect for jammed currency in the transport path between the width sensors and the reject sensor. Clear the terminal error code. The width sensor may be dirty. If the voltages are correct; and the cables are undamaged and correctly connected; causes of this error may be a defective cable; a defective printer; printer control board; or the main navigate here

Clean the exit sensor using a soft brush and a vacuum cleaner. Cassettes with no identity must be injected with a new cassette ID (See the 5000 Cash Dispenser Configuration Manual). Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 125 Initial status check failed 1. Georgia - Las Vegas Web Development by BestHive Skip navigation UploadSign inSearch Loading... http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Atm Error Code 148

Refer to error code 535. 548 Card Reader ñ End sentinel not found. Release the printer locking screw. Refer to error 522. 528 EJ sequence error. If no jam is located, remove the first note from the cassette.

Refer to error code 535. 537 Card Reader ñ Invalid Record. Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends. If the cable and connectors are good; replace the Electronic Journal Module. Triton Atm Error Code 101 Restart the cash dispenser.

Clear all errors and test the dispenser by completing several TEST DISPENSES. Remove any jammed currency.2. Test the dispensing mechanism by completing several Test Dispenses. 3. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php Replace the dispenser.

Refer to error 500. 514 SPED device bit stuck. Triton Traverse Error Code 917 If these actions have no effect on dispenser operation, print a dispenser status report, scan the click count history, starting at the bottom. Purge the dispenser using the purge command. Consult 183 Receipt printer paper is low 1.

Triton Error Code 244

Otherwise; replace the dispenser. 3.

If the problem persists; replace the dispenser. 55 (37h) Ram corruption A mechanical failure has occurred. Triton Atm Error Code 148 This occurs when the currency in any cassette reaches a thickness of approximately 25-35 mm. Triton Error Code 151 If the error clears, put the cash dispenser in service.

This error code is generated when a cassette is not open and any command other than open cassettes; reset; and close cassettes are sent to the system. http://u2commerce.com/error-code/triton-9100-atm-error-codes.html Make sure it is connected to CN1 on the printer control board. A normal return code for this test dispense operation is ì4 1 1 1 1? Purge the dispenser with the purge command under diagnostics. Atm Error Codes List

If the problem persists, replace the dispensing mechanism. 136 Modem initialization failed 1. Manage transactions, view top player activity online with our intuitive reporting site. Overcome space limitations while engaging customers with multiple marketing presentations utilizing videos, menu screens, avatars, widgets all on the same monitor; ultimately maximizing your retail footprint. http://u2commerce.com/error-code/triton-9100-error-code-206.html Make sure the shelf that the dispenser is mounted on is level and seated at all four corners. 3.

Make sure the access panel on the bottom of the note qualifier is closed and locked in position. Mitsubishi Triton Error Codes Complete several live dispenses to ensure the dispenser is working correctly. Reset the error.

Replace the dispensing mechanism. 54 Operation time-out 1.

  1. Verify that the diverter moves freely.
  2. If the error clears, put the cash dispenser in service. 5.
  3. Complete several Test Dispenses to verify correct operation.
  4. Purge the dispenser using the purge command from diagnostic menu. 2.
  5. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.
  6. Open the printer support bracket and verify that there are no jams in the printer or the paper path.
  7. Inspect main board to electronic journal (EJ) communication cable for damage.
  8. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.
  9. If the error persists replace the dispensing mechanism.chanism. 126 (7Eh) Diverter moved to reject position during dispense Inspect for a note jam at the diverter.

This error is not displayed at the Cash Dispenser. Verify the blue lever on the left side of the printer in the print position. Verify operation of the power supply. Triton 9100 Error Code 148 Test the dispenser by completing several test dispenses. 3.

If the diverter has excessive binding or appears damaged; replace the dispenser. 2. Reset the cash dispenser. Remove any documents from the tote transport. http://u2commerce.com/error-code/triton-9100-error-codes.html If the problem persists; replace the dispenser. 50 (32h) Interference recovery Possible static discharge.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Clear the jammed documents.2. Refer to error 500. 506 SPED invalid request. Inspect the printer data cable for damage.

Inspect the note diverter for proper operation and damage. Make sure it is seated at the main board and at the printer control board at CN6. 5. Autoplay When autoplay is enabled, a suggested video will automatically play next. Clear all errors and test the dispenser by completing several TEST DISPENSES.

If the DC voltages applied to the SPED board correct and the cables are in good condition and seated properly; replace the SPED board. 300 (30h)[0] Description: Successful Command The dispenser Please try the request again. belts; gears; cables; or sensors). See error code 557. 560 Unknown device error.

Possible may be a processor or telephone hardware problem (If problem persists call Your Service Provider or Triton Tech Support) 4 Error in modem data No money is dispensed; screen and If error persists; replace the dispenser mechanism. 371 Dispenser SDD com error header-trailer. If the error reoccurs the most likely causes of the problem may be note transport or CMC. 307(37h)[7] Transmission Error. Clear the error. 3.