If all sensors are operation correctly; and the error persists; replace the replace the dispenser. 42 (2Ah) Transport Error This is a timing wheel or timing wheel sensor error. 1. Inspect all communication cables to make sure they are not damaged. If these check are not properly completed replace the note qualifier. 326(4Ah)[J] Note feed sensor failure. If the sensor is blocked; remove the blockage. http://u2commerce.com/error-code/triton-9100-error-134.html
Replace the dispenser is the error persists. 360 Dispenser invalid return ID. Examine the timing wheel for physical defect. Refer to error code 535. 544 Card Reader ñ Invalid request. Remove any jammed currency.2.
Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is Otherwise, replace the dispenser.Note, if this occurs on a Mini Mech, only during a multi note dispense, the exit sensors may have become weak. This is error code will set an ìOut of Serviceî condition. Complete several live dispenses to ensure the dispenser is working correctly.
Clear terminal error code. Check the cable and connections from the docking station to the SPED board. If the error code is repeated; replace the note feeder or note feeder controller for the affected feed channel. 353(65h)[e] No message to resend. Triton Error Code 139 Inspect main board to electronic journal communication cable for damage.
Cracked or broken clips should be replaced 4. Triton Error Code 244 At least one character was received (ETX was never received). Inspect for jammed currency at the Diverter. https://www.nasatm.com/error_codes/code/206/ If these actions have no effect on dispenser operation; replace the dispenser mechanism. 119 (77h) Diverter in dispense position on start of dispense or learn 1.
Verify clearance at the diverter. Triton Atm Error Code 101 Refer to error 500. 505 SPED device busy. Clear terminal error code. Carefully remove the double detect module from the note qualifier.
Make sure the documents are fit condition. http://xufegesy.hoxty.com/triton-9100-error-code-206-230.php Inspect main board to electronic journal communication cable for damage. Triton Error Code Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 109 Time-out at Exit sensor 1. Atm Error Codes List A defective cassette may also cause this problem. 333(51h)[Q] Reject vault full.
Inspect the cassette and feed path for currency that is stuck together or jammed. 3. http://u2commerce.com/error-code/triton-9100-error-codes.html Inspect the dispensing mechanism for of damaged components or broken wires. 2. If the error persist, possible causes may be the modem or main board assembly. 193 Baud rate setting for electronic journal failed 1. If the error clears, put the cash dispenser in service. Triton Error Code 151
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. ATMs with NMD or Mini Mech dispensers require electronic journals with part number that start with “9600” or “09600”. 2. The upper RJ-45 port is used for downloading software only. navigate here Reset the cash dispenser.
Otherwise; replace the dispenser. 38 (26h) Blocked Exit Exit sensor blocked or open circuit. Mitsubishi Triton Error Codes Inspect main board to electronic journal communication cable for damage. See error code 557. 562 SPED error.
Refer to Section 4 of the RL5000 Installation and Service Manual or the RL5000 Quick Reference Guide for instructions. Test the dispenser by completing several test dispenses. 4. This error code occurs while running the dispenser on the NMD test software and when too many notes are requested during a dispense command. Triton 9100 Error Code 148 This error code is generated when the reject vault is not present or not properly installed.
If these actions have no effect, replace the dispensing mechanism. 50 Interference recovery Possible damage due to static discharge1. Inspect the currency for excessive wear. Refer to error 500. 507 SPED sequence error. http://u2commerce.com/error-code/triton-9100-atm-error-codes.html If the error persists; replace the dispensing mechanism. 104 (68h) Unable to clear width sensor.
This Triton 9100 Error Code 206 error code has a numeric error number and a technical description. Otherwise, it may be necessary to replace the dispenser.4. Clear the error. If the error does not repeat again; complete a live dispense to verify the note diverter moves the currency to the exit position.
Norton SystemWorks cfgwiz. Replace dispenser if error code persists. 395 Multiple cassette of the same type. Your cache administrator is webmaster. If the cables are undamaged, the main board or electronic journal may be defective 150 Status command to journal failed 1.
Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean. Check operational error code of dispenser. Your cache administrator is webmaster. If no jam is located, remove the first note from the cassette.
Remove each note feeder module from the dispensing mechanism and clean their associated empty; pressure and exit sensors with clean compressed air. Refer to error 522. 527 EJ invalid request. This error code is produced when the single reject event counter exceeds 50 reject events or the bundle reject event counter exceeds 250 notes. If the error clears, put the cash dispenser back in service.
If error fails to reset, or the error reoccurs in a short amount of time, consider replacing the SPED. 241 SPED Warning: Self Test error See Error Code 240 382 Dispenser