Home > Error Code > Triton 9100 Error Codes

Triton 9100 Error Codes

Contents

Inspect for jammed currency in the transport path between the width sensors and the reject sensor. Make sure it is connected to CN1 on the printer control board. Replace the dispenser if it is broken. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. this contact form

Verify that the diverter moves freely and is not binding. Generated Sun, 30 Oct 2016 17:59:09 GMT by s_wx1196 (squid/3.5.20) Problem: The ATM says "Communication Error" or "System Unavailable" Cause: The ATM may have developed a fault that prevents it from communicating with the network. PURGE the dispensing mechanism. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Error Code 244

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 122 Unexpected note at exit 1. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Test the dispensing mechanism by completing several test dispenses. Do several test dispense operations. 3.

The Triton Connect Host Computer generates this error when a terminal does not make a call to the Triton Connect Host Computer as requested. See Recommended Actions for Error Code 134 136 Modem initialization failed Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 122 (7Ah) Unexpected note at exit 1. Triton Error Code 139 If these actions have no effect on dispenser operation, replace the dispenser mechanism.

Clear the error. Reset the cash dispenser and clear the error. Inspect main board to electronic journal communication cable for damage. have a peek here Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 114 Exit blocked during purge 1.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Atm Error Code 3-da000(80) If the error clears, go to Step 9. Inspect the dispensing mechanism for jammed currency at the exit sensor. Check the calibration value for the pressure; empty; and exit sensors.

Atm Error Codes List

Inspect main board to electronic journal communication cable for damage. https://www.nasatm.com/error_codes/code/144/ Inspect the feed path for jammed notes. Triton Error Code 244 Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Triton Error Code 151 Please try the request again.

If the problem persists, replace the dispensing mechanism. 135 Feed sensor blocked as reported by status check 1. weblink Error Codes 139, 140, and 141: Printer Not Responding, Printer Timeout, and Paper Jam Solution: Open the ATM control panel and check printer paper path for blockage that could cause a The main board does not see any activity on TCP-IP. 1. Restart operating system. Mitsubishi Triton Error Codes

  1. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.
  2. Inspect the note diverter in the note transport module.
  3. It the error code repeats; verify the power supply output voltages are within expected values.
  4. Refer to error 522. 527 EJ invalid request.
  5. Inspect electronic journal to dispenser communication cable for damage.

Make sure that the exit sensor is clean and operation correctly. 3. Remove any jammed currency.2. Clean the sensors in the note transport a needed. http://u2commerce.com/error-code/triton-atm-9100-error-codes.html Verify the blue lever on the left side of the printer in the print position. 3.

If the problem persists; replace the note transport module. 348(60h)[ë] Dispenser internal error. Triton Atm Error Code 101 The reason that the error code is generated is the detection of an incorrect LRC character or a parity error. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.

Inspect the exit area to ensure nothing is blocking the exit sensor.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Release the printer locking screw. Power down the ATM in the proper sequence. Triton Error Code 246 There should be approximately 1/4 inch of currency (about 60 bills) in the Cassette at this point.

Possible may be a processor or telephone hardware problem (If problem persists call Your Service Provider or Triton Tech Support) 5 Connect 1200 Baud then lost carrier or connection. It is feasible that this error code could be generated even if the lifts are in the up position. Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends. http://u2commerce.com/error-code/triton-9100-atm-error-codes.html If the error does not occur again, put the cash dispenser in service.

Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean. Replace the dispenser is the error persists. 365 Dispenser BCC error. Test the dispenser by completing several test dispenses. 4. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 128 Error in reply from the dispenser mechanism 1.

See error code 557. 562 SPED error. Replenish paper as needed. If the error does not occur again put the cash dispenser in service. Verify the quality of your incoming TCP-IP connection and your TCP-IP configuration.

Inspect cable from the Electronic Journal to the dispenser to be sure both ends are securely screwed in place. When the note is stuck in the note transport sensor. 2. Restart the operating system. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

Refer to error 522. 533 EJ BCC error. Clear all errors and test the dispenser by completing several TEST DISPENSES. Verify that the diverter moves freely. 3. Refilling may be delayed for several transactions if the error code is the first warning that the cassette is nearly empty.

Place all belts on their rollers and gears. Refer to error code 535. 542 Card Reader ñ Device busy. Seat connectors or replace the power supply as needed. 2.