Home > Error Code > Triton 9600 Error 134

Triton 9600 Error 134

Contents

If the problem persists; replace the dispenser. 36 24h) Mistracked note at exit Inspect the cassette and feed path for jammed notes. Clear all errors and test the dispenser by completing several TEST DISPENSES. Replace the power supply if necessary. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. this contact form

Inspect the feed path for any jammed notes. Clear the error. Release the printer locking screw. The modem may be defective.8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT2000165Electronic journal not present1. https://prineta.com/atms/docs/atm-error-codes-triton-machines/

Triton Atm Error Code 148

Check to make sure that cables connecting the note transport and the CMC module are not damaged. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT2000104Unable to clear width sensor.Remove the cassette and inspect Inspect for a currency jam at the diverter. 2. If the error code is repeated; replace the note feeder or note feeder controller for the affected feed channel. 353(65h)[e] No message to resend.

Examine the timing wheel for physical defect. Make sure it is connected to CN1 on the printer control board. Make frequent, rapid and/or scheduled changes to your messages with ease. Triton Atm Error Code 101 If the error clears, put the cash dispenser in service.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. If the problem persists; replace the dispenser. 35 (23h) Mistracked note at double detect This is a double detect fault. for a four cassette dispenser. https://www.nasatm.com/error_codes/code/134/ Test the dispensing mechanism by completing several Test Dispenses. 3.

Clear the error. Triton Traverse Error Code 917 Open the extension. Reset the cash dispenser. Replace the dispenser is the error persists. 365 Dispenser BCC error.

  • Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.
  • If the error does not occur again; put the cash dispenser in service. 4.
  • Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct.
  • Download to Triton Connect.
  • This status code will appear in the electronic journal as code 32 indicating the successful completion of a transaction.8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT200033Feed FailureThis error is
  • Restart the operating system.
  • Clear all errors and test the dispenser with a live transaction.
  • Verify that the currency is properly installed in the cassette.
  • Replace the dispenser if it is broken.

Triton Error Code 244

Purge the dispenser using the purge command. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php The completion of a satisfactory printer self test indicates that the current Printer/Printer Control Board combination and its interconnected wiring are operating normally. Triton Atm Error Code 148 Clean as needed with soft brush and vacuum cleaner. 2. Triton Atm Error Code 151 There can be many events which may have resulted in the system files errors.

A normal return code for this test dispense operation is ì4 1 1 1 1? weblink If the status clears and the return code are normal place the cash dispenser in service. Clear the jammed documents. 2. Inspect for jammed Currency in the feed path and at the Exit sensor. Atm Error Codes List

Inspect the feed path for jammed notes. Refer to error 522. 534 EJ device reset. If the problem remains after reloading the cassette; replace the cassette; the denomination extension; or the note feeder controller associated with the cassette causing the problem. 351(63h)[c] Module needs service. navigate here Refer to error code 535. 542 Card Reader ñ Device busy.

Clear as necessary and perform both printer diagnostic tests as outlined in Recommended Actions for Error Code 138 142 Dispenser returns bad command error The most likely cause of this error Mitsubishi Triton Error Codes Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. All cassettes have reached low cash level.

Otherwise, the possible causes of the problem may be a defective paper low sensor, cable, docking assembly or.

Purge the dispenser using PURGE command. Refer to error code 535. 547 Card Reader ñ Start sentinel not found. Inspect card reader for foreign objects. Triton 9100 Error Code 148 Make sure it is connected to CN1 on the printer control board.

If the diverter has excessive binding or appears damaged; replace the dispenser. 2. The dispenser will shut down, possibly resulting in trailing notes stopping in the path. 1. All Rights Reserved.

How to fix Sql Server Error Logging Level Error? his comment is here Inspect cassettes.

Reload cassettes. This error will place the cash dispenser ìOut of Serviceî. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 112 (70h) Timeout waiting for leading edge at reject A note that was expected to be seen by Place the machine into service.9600, 9800, RL1600, RL2000, RL5000, RT200062Loss of power during paymentReset the ATM.

This article contains information that shows you how to fix Sql Server Error Logging Level both (manually) and (automatically) , In addition, this article will help you troubleshoot some common error Purge the dispenser using the purge command from diagnostic menu. 2. Verify that the diverter moves freely and is not binding. Inspect for jammed currency in the transport path between the width sensors and the reject sensor.

Make sure the tamper screw is secure to the SPED module. To clear an Error 182: 1. Change baud rate settings. 4. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.

Clear the error and perform a test dispense. Clean and verify the operation of the exit sensor. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT2000109Time-out at Exit sensor1. Do several test dispense operations.