Home > Error Code > Triton Atm Error Code 113

Triton Atm Error Code 113

Contents

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Complete several live dispenses to ensure the dispenser is working correctly. If the error clears, put the cash dispenser in service. Inspect the feed path and exit sensor for jammed currency and broken components. this contact form

Replace the dispensing mechanism. 53 EPROM error A mechanical failure has occurred. Inspect the printer data cable for damage. Test the dispenser by completing several test dispenses. Do several test dispense operations. 4. https://www.nasatm.com/error_codes/code/113/

Atm Error Codes List

If a belt displays excessive wear or damage you may be able to replace it. Inspect the detent clips (the clips that hold the cassette in place). Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. Clear the error.

Remove any jammed currency. 2. gateway IP address, ports, etc.) 238 Dispenser Compromise A reset has occurred in the middle of a dispense. 1. If it works with the door open, remove obstruction causing the diverter to contact the vault door. 4. Atm Error Code 3-da000(80) Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.

If the problem persists, remove the main board and replace the modem. 3. Triton Error Code 244 Make sure the connectors are seated securely on the main board and on the electronic journal. 2. If these actions have no effect, replace the dispenser. 45 Diverter error This error occurs when the diverter is in the wrong position during a dispense.1. Open the printer support bracket and verify that there are no jams in the printer or the paper path.

Keyword search will match on all words; a single keyword will; provide the maximum amount of results. Mitsubishi Triton Error Codes If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Verify that there is paper in the printer. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.

  • If these actions have no effect, replace the dispenser. 51 Accountancy error A mechanical failure has occurred.
  • If the voltages are not within tolerance, the cable or power supply may be defective. 4.
  • Make sure the connectors are seated securely on the main board and on the electronic journal. 2.
  • Inspect the printer data cable for damage.
  • It can occur if there are notes already in the transport before the start of a transaction or if the exit sensor is blocked. 1.
  • Inspect electronic journal to dispenser communication cable for damage.
  • Verify the blue lever on the left side of the printer in the print position. 3.
  • Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3.
  • If the voltages are not within tolerance, the cable or power supply may be defective. 4.

Triton Error Code 244

Enter the Management Functions and configure the bill size. 187 Maximum withdrawal not configured Enter the management functions and configure the “multiple amount” parameter. view publisher site ATMs with NMD or Mini Mech dispensers require electronic journals with part number that start with “9600” or “09600”. 2. Atm Error Codes List Other components that may cause this error are the main board or the dispensing mechanism. 129 No response from the dispenser mechanism 1. Triton Error Codes The paper low sensor may be dirty and require cleaning. 4.

Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean. weblink Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 109 Time-out at Exit sensor 1. Test the dispenser by completing several test dispenses. If the error clears, put the cash dispenser in service. 6. Triton Error Code 151

Clean the exit sensor using a soft brush and a vacuum cleaner. If the error clears, put the cash dispenser in service. 5. Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. http://u2commerce.com/error-code/triton-atm-error-code-148.html Inspect electronic journal to dispenser communication cable for damage.

The system returned: (22) Invalid argument The remote host or network may be down. Atm Error Codes 072 If the test dispenses pass, but the error returns upon live dispenses, do dispenses with the vault door open. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.

Place all belts on their respective rollers and gears.

The modem may be defective. 165 Electronic journal not present 1. How To Fix Triton Error Code 113 Errors In GM Master Option Code List - Scribd - GM Master Option Code List - Ebook download as PDF File .pdf , Text Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 104 Unable to clear width sensor. Triton Error Code 139 Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON.

This status code will appear in the electronic journal as code 32 indicating the successful completion of a transaction. 33 Feed Failure This error is usually associated with an empty note Verify the blue lever on the left side of the printer in the print position. 3. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 2. http://u2commerce.com/error-code/triton-atm-error-code-110.html Make sure they are seated at the printer control board and not damaged. 6.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Otherwise, replace the dispenser.Note, if this occurs on a Mini Mech, only during a multi note dispense, the exit sensors may have become weak.