Home > Error Code > Triton Atm Error Code 148

Triton Atm Error Code 148

Contents

Display should read "20 20 21". Inspect the cables connected to CN2, CN3, CN4, and CN5. Refer to error 500. 502 SPED read type error. If the status clears and the return code are normal place the cash dispenser in service. this contact form

Inspect the cassette and feed path for currency that is stuck together or jammed. 3. Probable cause for this error is a faulty or uncalibrated double detect module, or a jammed currency in the double detect.1. Clear terminal error code. If the voltages are not within tolerance, the cable or power supply may be defective. 4. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Error Code 244

Verify that all DC voltages applied to the printer control board are correct. Other components that may cause this error are the main board or the dispensing mechanism. 130 Command not acknowledged by the dispenser mechanism 1. Clear the error. Inspect the documents in each cassette to insure they are in fit condition.

If these actions have no effect on dispenser operation, print a dispenser status report, scan the click count history, starting at the bottom. Refer to error code 535. 549 Card Reader ñ Parity error. Make sure the connectors are seated securely on the main board and on the electronic journal. Mitsubishi Triton Error Codes Verify the quality of your incoming TCP-IP connection and your TCP-IP configuration, (i.e.

After an ATM reset, the "Reset Error" and "Management" options will appear. Triton Atm Error Code 151 This error code will place the cash dispenser ìOut of Serviceî. Test the dispensing mechanism by completing several test dispenses. If error persists; replace the dispenser mechanism. 375 Dispenser invalid request.

Verify that all DC voltages applied to the printer control board are correct. Triton Traverse Error Code 917 Otherwise; replace the dispenser. 37 (25h) Note too long at exit Note was temporarily caught at exit. Clear all errors and test the dispenser by completing several test dispenses. Check paper status.

Triton Atm Error Code 151

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. More Help If the error clears; put the cash dispenser in service. 6. Triton Error Code 244 Seat connectors or replace the power supply as needed. 2. Atm Error Codes List Unplug the cable and connect the base unit of a telephone.

EOT was received as first character after sending a NAK due to a bad response message. weblink Verify that all DC voltages applied to the printer control board are correct. Open all access panels and inspect for jammed documents and other debris. Release the printer locking screw. Triton Atm Error Code 101

Seat connectors or replace the power supply as needed. 2. Triton Connect error. The dispenser sends this status code when a command has been successfully executed. http://u2commerce.com/error-code/triton-atm-error-code-110.html Check with the processor. 144 No reply from the Electronic Journal Inspect cable to ensure it is securely attached to the Backplane at J4 and at the Electronic Journal.

Inspect all communication cables to make sure they are not damaged. Triton Error Code 246 Clear all error and purge the dispenser using the purge command. 4. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism.

This is a timing wheel or timing wheel sensor error.. 1.

Test the dispenser by completing several test dispenses. 3. Please try the request again. Check to make sure that cables connecting the note transport and the CMC module are not damaged. Triton 9100 Error Code 148 If these actions have no effect on dispenser operation, replace the dispenser mechanism.

If the voltages at PL2 are incorrect; check all pins on cable 09600-00013 for continuity from end-to-end. Replace the exit sensor if defective. If the error clears, put the cash dispenser in service. 5. his comment is here Place all belts on their rollers and gears.

Replace dispenser if error code persists. 395 Multiple cassette of the same type. If the error persists; replace the dispensing mechanism. 103 (67h) Thickness sensor unstable Enter the diagnostic function and complete the ìlearn note thicknessî command. Test the dispenser by completing several test dispenses. The next entry, below 116, is the Hardware Status.

The cables may be defective. 3. If all sensors are operation correctly, and the error persists, replace the replace the dispenser. 42 Transport error. If the error persists, replace the dispenser. 46 Exit quantified This status appears when the count at the exit is greater than the number of documents requested.1. Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends.

Check data and power connections to the dispenser device. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Purge the dispenser with the purge command. If error persists; replace the SPED module. 565 Cabinet door open.

Inspect electronic journal cabling. An attempt to feed or dispense documents has been made when there is a note in the note transport throat. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. Refer to error 500. 520 SPED device reset.

This error will place the cash dispenser ìOut of Serviceî.