Home > Error Code > Triton Atm Error Code 188

Triton Atm Error Code 188

Contents

This status code will appear in the electronic journal as code 32 indicating the successful completion of a transaction. 33 Feed Failure This error is usually associated with an empty note Clear the jammed documents.2. Clean the width sensor with compressed air. If the error clears, put the cash dispenser in service. 5. navigate here

Purge the dispenser using the purge command. Inspect the dispensing mechanism for of damaged components or broken wires. 2. This is done to indicate that the power has been off. The most probable cause is either mechanical or electrical failure of the note diverter in the note transport module. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php

Triton Atm Error Code 101

Please try the request again. Complete several Test Dispenses to verify correct operation. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

Perform the test dispense function several times (two or three). Make sure it is seated at the main board and at the printer control board at CN6. 5. Refer to error 522. 533 EJ BCC error. Triton Atm Error Code 144 If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main

Determine what is causing the cassette to not stay locked in place. 4. Triton Atm Error Code 151 If injecting a new cassette ID into the cassette does not correct the problem; replace the cassette. 322(46h)[F] Main motor failure Error code 322 is generated when the main motor fails Inspect the cables connected to CN2, CN3, CN4, and CN5. http://www.atmdepot.com/triton-atm-error-codes/ Verify that all sensors are operation correctly.

If error code re-occurs; disable low paper checking and place the terminal back into operation. Triton Atm Error Code 112 Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Replace the note qualifier or note transport if the problem persists. 310(3Ah)[:] Cassette not properly installed. broken belts; broken gears; disconnected or damaged cables; broken timing wheel etc.).

  1. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.
  2. Inspect main board to electronic journal communication cable for damage.
  3. The cables may be defective. 3.
  4. If error persists, replace the SPED keypad module. 207 SPED not detected This Error/Status Code is valid for units with SPED keypad device installed. 1.
  5. If the error code is reported again; replace the CMC module.
  6. Replace the dispenser if it is broken.
  7. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 102 Timeout at Exit Sensor 1.
  8. Host hung up.
  9. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 5.

Triton Atm Error Code 151

If these actions have no effect on dispenser operation; replace the dispenser mechanism. 118 (76h) Exit sensor blocked on start of dispense or learn 1. http://atmms.com/ Test the dispenser by completing several test dispenses. 4. Triton Atm Error Code 101 Remove jammed currency. 2. Triton Atm Error Code 245 Reset the cash dispenser.

Once records have been viewed or saved, they need to be marked as audited. check over here Clear the error. If these actions have no effect on dispenser operation, replace the dispenser mechanism. Inspect the cassette and feed path for notes that are stuck together or jammed. Triton Atm Error Code 33

Reset the cash dispenser. Inspect the feed path and feed sensors for jammed documents and broken components. Reset the cash dispenser. http://u2commerce.com/error-code/triton-atm-error-code-148.html Inspect for a jammed currency in the reject sensor. 2.

If the error clears; put the cash dispenser in service. 4. Triton Atm Error Code 135 Restart the operating system. Refer to Section 5 of the RL5000 Service Manual or the RL5000 Quick Reference Guide for instructions. 2.

Purge the dispenser.

Use the reject channel error code function to verify the operation of the sensors on the note transport module. Otherwise; replace the dispenser. 38 (26h) Blocked Exit Exit sensor blocked or open circuit. Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Triton Error Code 244 Make sure the tamper screw is secure to the SPED module.

Refer to error code 535. 554 Card Reader ñ device reset. Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette. Test the TDM-100 by completing several Test Dispenses. http://u2commerce.com/error-code/triton-atm-error-code-110.html On an 8 bit machine, such as 9100 or 9600, choose Diagnostics>More>More Keypad>Clear Tamper. 240 SPED Self Test Error The SPED has returned an error during self test. 1.

If the error clears; put the cash dispenser in service. 3. Remove any jammed currency. 2. Remove the cassette and inspect the dispenser’s feed path for jammed currency and other debris in the double detect assembly. Inspect the incoming power and check for proper grounding 51 (33h) Suspect exit accountancy A mechanical failure has occurred.

Inspect the cable supplying DC power from the power supply to the printer. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 126 Diverter moved to reject position during dispense Inspect for a note jam at the diverter.