This error code is generated by the dispensing mechanism when the calibration value for at least one of the sensors in any of the note feeders has exceeded the upper limits Inspect the printer data cable for damage. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 125 Initial status check failed 1. The feed sensors may be dirty. this contact form
If these actions have no effect on dispenser operation, replace the dispenser mechanism. If the problem persists; replace the dispenser. (see error 37 above for step by step diagnostics) 39 (27h) Too many notes Clean the all sensors. If the problem persists; replace the dispenser. 55 (37h) Ram corruption A mechanical failure has occurred. It is feasible that this error code could be generated even if the lifts are in the up position.
Otherwise, replace the dispensing mechanism. Inspect the note transport and delivery throat make sure all belts are on track and there are no documents jammed in the transport or exit areas. If two or more of the same type cassette are installed; inject a new cassette ID into one of the cassettes that is different from the other cassette. 101 (65h) 2-second Reseat connections.
If the error clears put the Cash Dispenser into service. If the error code has been cleared; the cash dispenser can be put back in service. If these actions have no effect on dispenser operation, replace the dispenser mechanism and/or the note cassette. Mitsubishi Triton Error Codes Make sure the battery is seated secure in the battery holder. 2.
All Rights Reserved.
Install the cassette. Atm Error Codes 072 If the cables are undamaged, the main board or electronic journal may be defective 146 No reply from command to electronic journal 1. Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette. Detected offline error check op state.
The width sensor may be dirty. Read More Here If the voltages are not within tolerance, the cable or power supply may be defective. 4. Triton Error Code 244 If the cable appears to be in acceptable condition; verify that the voltages at PL2 on the back of the dispenser are correct. Triton Error Code 151 If not, place in service using the Cassette Service menu option.
Restart operating system. weblink Clear any jammed currency. 2. If the cables are undamaged, the main board or electronic journal may be defective 162 Electronic Journal get serial number failed 1. Replace the dispenser. 56 (38h) Link error Configuration jumpers have been changed. Atm Error Code 3-da000(80)
Clear all errors and test the dispenser with a live transaction. If the error code is reported again; replace the CMC module. Release the printer locking screw. navigate here Refer to error 500. 504 SPED invalid return ID.
If the error persists; replace the SPED keypad module. 206 SPED could not perform a successful command within SPED_MAX_ATTEMPTS tries Error code valid only for units with SPED keypad device installed. Triton Error Code 139 Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Verify that the identity of each cassette can be read through read cassette ID function (See the 5000 Cash Dispenser Configuration Manual).
Test the dispenser by completing several test dispenses. 3. It will also be stored as part of the transaction data in the electronic journal. Clear the error. 3. Triton Atm Error Code 101 Use clean compressed air to remove any dust or dirt from the sensor lenses.
After about ten seconds, push the Power ON/OFF switch to the ON position to start the terminal. 3. Verify that the both ends of each cable are securely connected to its termination points. Enter the management functions and attempt to complete the print journal command. his comment is here If the error clears; put the cash dispenser in service. 4.
Clear the error. 3. The Triton Connect Host Computer generates this error when a terminal does not make a call to the Triton Connect Host Computer as requested. Can only be cleared in Diagnostics>Keypad>Clear Tamper. Make sure the battery is seated securely in th battery holder.
Inspect the note qualifier for any damage (i.e. Replace the dispenser if it is broken. Otherwise; it may be necessary to replace the dispenser. 4. If the cables are undamaged, the main board or electronic journal may be defective 153 Electronic journal mode 1.
Open all access panels and remove any jammed documents from the transport path. Inspect card reader for foreign objects. Check the operation of all sensors in the note transport module.