Verify that all DC voltages applied to the printer control board are correct. Dispenser failed to identify the dispenser type installed. Open the Security Cabinet and inspect the cash dispenser for broken parts. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. http://u2commerce.com/error-code/triton-rl2000-error-codes.html
Refer to error 522. 526 EJ device busy. EOT was received as first character after the first request message was sent. 2. Press the reset error key. 4. Clear the error. https://prineta.com/atms/docs/atm-error-codes-triton-machines/
a. Clear the error. If the error is repeated; proceed to the next paragraph. If cash dispenser operates normally when performing the test dispense function; put the cash dispenser in service.
Clear as necessary and perform both printer diagnostic tests as outlined in Recommended Actions for Error Code 138 142 Dispenser returns bad command error The most likely cause of this error If the test dispenses are completed normally, and the return code are correct, clear all errors and place the cash dispenser in operation.b. Verify the blue lever on the left side of the printer in the print position. 3. Atm Error Codes List It can occur if there are notes already in the transport before the start of a transaction or if the exit sensor is blocked. 1.
If the error persists; replace the dispensing mechanism. 111 (6Fh) Diverter timeout 1. Purge the dispenser with the purge command under diagnostics. This status is generated if the double detect is unable to calibrate. Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean.
See error code 557. 560 Unknown device error. Triton Error Code 139 Clear the jammed documents.2. Make sure that note qualifier and the note transport modules are mechanically aligned. Consult9600, 9800, RL1600, RL2000, RL5000, RT2000182Currency cassette low.
If the error persists; replace the dispensing mechanism. 108 (6Ch) Unexpected note at double detect A note has been detected in the double detect sensor without being detected at the width Verify that all access panels are closed and secured. Triton Error Code 244 Refilling may be delayed for several transactions if the error code is the first warning that the cassette is nearly empty. Triton Error Code 151 Verify the physical presence of each cassette.
Make sure the ribbon cable from the docking station go the card reader is fastened at both ends of the cable and the orientation of the cable is correct. weblink Cassettes are taken out of service because of feed failures or excessive rejects. 1. If problem persistes; see Error Code 138 196 Card Reader Failure Inspect the card reader assembly. This error code will place the cash dispenser in an ìOut of Serviceî condition. Mitsubishi Triton Error Codes
Verify the blue lever on the left side of the printer in the print position. 3. If the error code is reported again; replace the CMC module. 309(39h) Jam in Note Qualifier. Restart operating system. http://u2commerce.com/error-code/triton-error-codes-144.html Replace the exit sensor if necessary.4.
Clear terminal error code. Triton Atm Error Code 101 Replace the dispensing mechanism.8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT200053EPROM errorA mechanical failure has occurred. The modem or the main board may cause the problem.
Verify that the Reject Vault and one cassette are present in the dispenser mechanism. This error code is generated when a document from a note feeder fails to reach the note qualifier with in a specified time. Power down the ATM in the proper sequence. Triton Error Code 246 Inspect main board to electronic journal communication cable for damage.
Clear the error. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. Clear the error. his comment is here Otherwise, replace the dispenser.2.
If the problem persists, replace the dispensing mechanism9600, 9800, RL1600, RL2000, RL5000, RT200057Invalid data commandReset the ATM. If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main