To fix the problem, you have to know its root cause, it will also help you at least prevent it to happen again in the future. Verify that the SPED board has the correct DC voltages applied to it. Replace the dispensing mechanism. 56 Link error 1. Reset the error. this contact form
Test the dispenser by completing several test dispenses. Once the cause has been resolved, place desired cassettes into service and reset the error. If the status clears and the return code are normal place the cash dispenser in service. Recommended Action: This status is generated if the double detect is unable to calibrate. https://www.nasatm.com/error_codes/code/110/
Autoplay When autoplay is enabled, a suggested video will automatically play next. No characters were received. If the error clears, put the cash dispenser in service. 6. Reset the cash dispenser and clear the error.
Error Code: 187 Description: Maximum withdrawal not configured. Error Code: 5 Description: Connect 1200 Baud then lost carrier or connection. Recommended Action: See the recommended action for error code 144. Atm Error Code 072 Place all belts on their respective rollers and gears.
This problem may also be caused by a defective modem. Atm Error Code 3-da000(80) If the error clears, put the cash dispenser in service. 4. If the problem persists, replace the dispensing mechanism. The exit sensor may be dirty.
A temporary fix to this problem may be to set the “low receipt paper” parameter to “in service” so that the terminal software does not read the input from the low Atm Error Code 68 It the status clears, place the cash dispenser in service. Clear any jammed currency. 2. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.
Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. If these actions have no effect on dispenser operation, replace the dispenser mechanism. Atm Error Codes List Result: No money is dispensed, screen and receipt display system unavailable. Atm Error Code 3-da001 Verify that all access panels are closed and secured. 3.
Results Per Page: 20 50 100 All # Type Make Model Description No results found. weblink Allowable bill sizes are 5, 10, 20, 50, and 100. Install a new roll of paper if needed. 2. If the error clears, put the cash dispenser in service. 3. Triton Atm Error Codes
Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. Used up all radial attempts and got No Dial Tone for each attempt. 2. Clear the error. 4. navigate here Inspect the feed path and Feed sensors for jammed currency and broken components.
Cassettes are take out of service for two reasons: A) Feed failure or empty. Atm Error Code 068 The width sensor may be dirty. Make sure the tamper screw is secure to the SPED module.
If the voltages are not within tolerance, you may need to replace the cable or power supply. Test the dispenser by completing several test dispenses. If the error persists, replace the dispenser. Triton Error Code 244 Recommended Action: See recommended action for error code 138.
Make sure it is seated at the main board and at the printer control board at CN6. 5. If the error does not occur again, put the cash dispenser in service. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. his comment is here If the error persists in may be necessary to replace either the cassette or dispensing mechanism.
Loading... Verify that all access panels are closed and secured. Ensure the reject bin is empty, or that there is enough room for the rejects and test notes to fall into the reject bin. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 106 FIFO error The dispensing mechanism may have corrupt software.
Verify that the diverter moves freely and is not binding. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. Error Code: 353(65h)[e] Description: No message to resend. It may be necessary to replace the dispenser. 200 Dispenser fed extra note into stacker This status appears when the count at the exit can not be guaranteed. 1.
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Release the printer locking screw. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 105 Insufficient notes to learn from There may be an insufficient number of notes in the cassette Verify that all DC voltages applied to the printer control board are correct.