Remove jammed currency. 2. Recommended Action: This status occurs when a note is detected by the exit sensor when it should not have been. Recommended Action: This error code will occur only in cash dispensers running ACS terminal software. Inspect the documents in each cassette to insure they are in fit condition. this contact form
Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. Causes of the error: Windows Triton Error Code 197 are caused by misconfigured system files. If the problem persists, replace the dispensing mechanism 100 Good operation No Action Necessary. Inspect all cables for damage. https://www.nasatm.com/error_codes/code/error_197/
Error Code: 125 (7Dh) Description: Initial status check failed Recommended Action: 1. If the problem persists, replace the dispensing mechanism. Place all belts on their respective rollers and gears.
Clear the error. A mechanical error has occurred. Allowable bill sizes are 5, 10, 20, 50, and 100. Triton Error Code 139 Inspect electronic journal to dispenser communication cable for damage.
Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Triton Error Code 244 Other components that may cause this error are the main board or the dispensing mechanism. 129 No response from the dispenser mechanism 1. Inspect the feed path for jammed currency. If the error clears put the Cash Dispenser into service.
Recommended Action: Restart the operating system. Triton Atm Error Code 101 Recommended Action: Verify that the Printer has paper in it. Clear terminal error code. Other components that may cause this error are the main board or the dispensing mechanism. 144 No reply from the electronic journal. 1.
Results: No money is dispensed, screen and receipt display system unavailable. https://books.google.com/books?id=AHUcCgAAQBAJ&pg=PA197&lpg=PA197&dq=triton+error+197&source=bl&ots=p3fEg4z9K5&sig=AXg5wkZwS80o07BpLc3Dq9qlr5o&hl=en&sa=X&ved=0ahUKEwjv-MLDjO7PAhWg8oMKHVVQAHkQ6AEIQDAG If the voltages are not within tolerance, the cable or power supply may be defective. 4. Triton Atm Error Codes Inspect for jammed currency in the feed path and at the Exit sensor. Triton Error Code 151 Inspect the note transport sensor for blockage.
Clear all errors and test the dispenser with a live transaction. weblink Verify that all access panels are closed and secured. Perform a live transaction. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 112 Timeout waiting for leading edge at reject A note that was expected to be seen at Atm Error Codes List
Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 103 Thickness sensor unstable Enter the diagnostic function and complete the “learn note thickness” command. Inspect the cables connected to CN2, CN3, CN4, and CN5. Inspect the cable supplying DC power from the power supply to the printer. navigate here Error Code: 207 Description: SPED not detected.
Test the dispenser by completing several test dispenses with the test dispense command. Triton 9100 Error Code 148 If the error clears put the Cash Dispenser into service. Recommended Action: This status is generated when there are 8 rejects during the current dispense.
Reset the error code. Error Code: 301(31h) Description: Low level in cassette. The cables may be defective. 3. Triton Error Code 246 Inspect the feed path for any jammed notes.
Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 107 Time out waiting for FIFO The dispenser is reporting the leading note has not cleared the Error Code: 349(61h)[a] Description: Cassette lock faulty. Inspect main board to electronic journal communication cable for damage. his comment is here If these actions have no effect, replace the dispenser 55 RAM corruption A mechanical failure has occurred.
Time-out waiting for response or carrier was dropped. If the error recurs, a faulty cassette, note feeder or CMC module may be cause the problem. Error Code: 187 Description: Maximum withdrawal not configured. Inspect main board to electronic journal communication cable for damage.
Clean the sensors a needed. 3.