Home > Error Code > Triton Error 33

Triton Error 33

Contents

Recommended Action: Check data and power connections to the dispenser device. Modem response was good, but operation was not performed. 2. If the cables are undamaged, the main board or electronic journal may be defective 150 Status command to journal failed 1. If all sensors are operation correctly, and the error persists, replace the replace the dispenser. navigate here

Recommended Action: This status is generated when there are 8 rejects during the current dispense. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Cracked or broken clips should be replaced 4. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Atm Error Codes List

Verify that the diverter moves freely. If they pass, clear the error and place the ATM in service. 2 If working with a 9100 print a test receipt printer Verify the “Cassette 195 Receipt printer out of If these actions have no effect on dispenser operation, replace the dispenser mechanism. This problem may also be caused by a defective modem.

  1. If the cables are undamaged, the main board or electronic journal may be defective 147 Error in reply from electronic journal. 1.
  2. Verify clearance at the diverter.
  3. Replenish the paper.
  4. Inspect the printer data cable for damage.
  5. Clear all errors and test the dispenser by completing several test dispenses.
  6. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.
  7. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 110 Trailing edge time- out at exit. 1.
  8. Recommended Action: Enter management functions and configure the maximum amount.

If the status clears and the return code are normal place the cash dispenser in service. Otherwise, replace the dispensing mechanism. Test the dispensing mechanism by completing several test dispenses. Triton Atm Error Code 101 Inspect main board to electronic journal communication cable for damage.

Error Code: 318(42h)[B] Description: Too many notes requested. Triton Error Code 244 If you are not using TCP-IP / Ethernet for transactions or Triton Connect, ensure you do not have TCP-IP selected for any option in processors, communications or Triton Connect. 2. Make sure the battery is seated secure in the battery holder. 2. Error Code: 140 Description: Time-out waiting for printer to be ready.

Proceed by following procedures for error code 109 or 112. 108 Unexpected note at double detect A note has been detected in the double detect sensor without being detected at the Atm Error Codes 072 Inspect the feed path for jammed currency. ATMs with NMD or Mini Mech dispensers require electronic journals with part number that start with “9600” or “09600”. 2. Baud rate set to high for telephone line conditions.

Triton Error Code 244

Recommended Action: This error code is generated when a cassette is not open and any command other than open cassettes, reset, and close cassettes are sent to the system. view publisher site Inspect for jammed currency in the feed path and at the Exit sensor. Atm Error Codes List If the error persists, replace the dispensing mechanism. Triton Error Code 151 Error Code: 133 Description: +5 VDC not present on carrier detect.

If the cables are undamaged, the main board or electronic journal may be defective 158 Format command to electronic journal failed 1. check over here If it is necessary to check continuity of the cable assembly, refer to Appendix B for pinout of the cable assembly. The journal on these machines should be printed on a regular basis (i.e. Clear terminal error code. Atm Error Code 3-da000(80)

Reset the error. Recommended Action: See the recommended action for error code 128. Error Code: 112 (70h) Description: Timeout waiting for leading edge at reject Recommended Action: A note that was expected to be seen by the reject sensor was not detected by the his comment is here If no jams are found, remove the note closest the the pick rollers in the cassette. 3.

Verify that there is paper in the printer. Mitsubishi Triton Error Codes Install the cassette. Release the printer locking screw.

Error Code: 114 (72h) Description: Exit blocked during purge Recommended Action: 1.

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Remove jammed currency. 2. Triton 9100 Error Code 148 If the error is repeated, proceed to the next paragraph.

Telephone hardware problems. Verify the physical presence of each cassette. Clean as needed with soft brush and vacuum cleaner. 2. weblink Great rates with no hidden fees; ATM Merchant Systems offers long-term low processing rates you can count on paired with outstanding service and support you can trust.

This error code will cause the cash dispenser to go "Out of Service". If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Recommended Action: This error is usually associated with ""unfit"" currency or an empty cassette. 1. Your cache administrator is webmaster.

Refill the cassette as needed. 2. Clear terminal error code. Make sure all connectors attached to the CMC are seated in their receptacles. Verify that the both ends of each cable are securely connected to its termination points.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. This status is reported if the exit sensor is covered for a longer that allowed time for the current notes.1 Inspect the note transport and delivery throat make sure all belts Inspect for jammed currency in the feed path and at the Exit sensor. Recommended Action: See the recommended action for error code 144.

Otherwise, the possible causes of the problem may be a defective paper low sensor, or a defective printer control PCB. If the problem persists, replace the dispensing mechanism. Recommended Action: Error code valid only for units with SPED keypad device installed. If the error persists in may be necessary to replace either the cassette or dispensing mechanism.