Release the printer locking screw. Inspect electronic journal to dispenser communication cable for damage. If a belt displays excessive wear or damage you may be able to replace it. Error code 320 will not put the cash dispenser ìOut of Service. this contact form
The reason that the error code is generated is the detection of an incorrect LRC character or a parity error. Complete several test dispenses. Open the printer support bracket and verify that there are no jams in the printer or the paper path. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.
Inspect electronic journal to dispenser communication cable for damage. Inspect the incoming power and check for proper grounding 51 (33h) Suspect exit accountancy A mechanical failure has occurred. Starting at the top; you should find 24 volts; -12 volts; no pin; 5 volts; ground; 5 volts and ground. Reset the cash dispenser.
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. If error persists; replace the dispenser mechanism. 370 Dispenser ñ SDD EOT error. Use the NMD test software (available to Triton Certified Service Technicians) and verify the operational error code of the dispenser. 391 Dispenser sensor failure. Atm Error Codes List Possible may be a processor or telephone hardware problem (If problem persists call Your Service Provider or Triton Tech Support) 5 Connect 1200 Baud then lost carrier or connection.
The cash dispenser may be turned OFF; or the telephone line is shared with some other device that connects to the line before the cash dispenser. Triton Error Code 151 Add currency as needed. 183 Receipt printer paper low Verify that a new spool of paper is needed. Test the dispenser by completing several test dispenses. 3. This error code is produced when the single reject event counter exceeds 50 reject events or the bundle reject event counter exceeds 250 notes.
Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Triton Error Code 101 State by verify if this is associated with error code 151. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Verify clearance at the diverter.
Refer to error code 535. 556 System timeout. If the error reoccurs the most likely causes of the problem may be note transport or CMC. 307(37h) Transmission Error. Triton Error Code 244 If the error clears; put the cash dispenser in service. 5. Triton Error Code 236 A temporary fix to this problem may be to set the “low receipt paper” parameter to “in service” so that the terminal software does not read the input from the low
Note: This error code is often caused by a SPED tamper. weblink This error code will be generated when the following conditions occur: 1. b. Otherwise; replace the dispenser. 3. Mitsubishi Triton Error Codes
If error code reoccurs; replace the note feeder module. 329(4Dh)[M] Notes in delivery throat. Refill the cassette as needed. 2. The exit sensor may be dirty. navigate here Make sure the diverter moves freely. 4.
Check the dispenser data and power cable connections. Triton Traverse Error Code 917 Note, if the EJ is connected to the load port of the 9100 main board, permanent damage may result. 2. Clean the sensors in the note transport a needed.
Got connected and never received ENQ within time-out period (14 Seconds). (If problem persists call Your Service Provider or Triton Tech Support) 13 BGD_DONE_GOOD No money is dispensed; screen and receipt Purge the dispenser. Replenish paper as needed. Triton Error Code 246 Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.
Refer to error code 535. 548 Card Reader ñ End sentinel not found. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 114 (72h) Exit blocked during purge 1. Refer to error 522. 531 EJ SOH error. his comment is here Check data and power connections to the dispenser device.
Inspect main board to electronic journal communication cable for damage. Purge the dispenser using the purge command. Replace the exit sensor if defective. Refer to error code 535. 552 Card Reader ñ Device received invalid request.
Inspect for jammed currency at the diverter. Your cache administrator is webmaster. Test the dispenser by completing several test dispenses. 5. Replace the dispenser is the error persists. 365 Dispenser BCC error.
Make sure it is connected to CN1 on the printer control board. ATMs with NMD or Mini Mech dispensers require electronic journals with part number that start with “9600” or “09600”. 2. Reset the cash dispenser and clear the error. Reset the cash dispenser.
This time the printout will indicate No Journal Records to Print. Inspect for jammed currency in the transport path between the width sensors and the reject sensor. Refer to error 500. 514 SPED device bit stuck. Inspect electronic journal to dispenser communication cable for damage.
If the error code is reported again; replace the CMC module. 309(39h) Jam in Note Qualifier. Reset the cash dispenser and clear the error. Purge the dispenser using the purge command. Verify the blue lever on the left side of the printer in the print position. 2.
It will be display as the hexadecimal number ì30î when running the dispenser with the NMD test software. 301 (31h) Low level in cassette.