Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 113 Timeout waiting for trailing edge at reject 1. Remove any unacceptable notes from the cassette. 2. Recommended Action: Restart the operating system. Verify that the diverter moves freely. this contact form
Inspect all documents for excessive wear. To activate it, click the "Start" button and enter "memory" in the "Run" field. Error Code: 51 (33h) Description: Accountancy error Recommended Action: A mechanical failure has occurred. Clean the dirty sensor, or replace the note transport as needed. https://www.nasatm.com/error_codes/code/113/
Remove each note feeder module from the dispensing mechanism and clean their associated empty, pressure and exit sensors with clean compressed air. Examine the timing wheel for physical defect. Access Atm Triton Error Codes Code: Description: Recommended Action: 0: No errors 32: Good operation: No action required. Suspect the main board, the TCP-IP connection device (Quad Port Board in 96XX, Docking board on RL, FT or RT) or the TCP-IP equipment. 237 TCP/IP device failed Out going commutations
Inspect the feed path for currency that is stuck together or jammed. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Clear any jammed currency. 2. Atm Error Code 3-da000(80) Recommended Action: Inspect the card reader assembly.
If the error clears, put the cash dispenser in service. 3. Atm Error Codes List Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is Host hung up. Clear terminal error code.
Recommended Action: See the recommended action for error code 128 Error Code: 134 Description: Exit blocked as reported by error code check. Mitsubishi Triton Error Codes Remove any jammed currency. 3. Open the Security Cabinet and inspect the cash dispenser for broken parts. Once they are displayed on the screen, print or save them to an external device.
If the error clears, put the cash dispenser in service. 6. find more Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends. Triton Error Code 244 The width sensor may be dirty. Triton Error Code 151 Refer to Section 5 of the RL5000 Service Manual or the RL5000 Quick Reference Guide for instructions. 2.
Then it will complete the test dispense function. weblink The feed sensors may be dirty. Remove any unacceptable currency from the cassette. 2. If the error clears, put the cash dispenser in service. 5. Triton Error Code 139
Inspect the feed path for jammed currency. Error Code: 194 Description: An attempt to dispense bills has been made when the cassettes are unlocked. Clean the exit sensor using a soft brush and a vacuum cleaner. http://u2commerce.com/error-code/triton-atm-error-code-148.html Reset the cash dispenser.
If it works with the door open, remove obstruction causing the diverter to contact the vault door. 5. Triton Atm Error Code 101 Error Code: 305(35h) Description: Diverter Failure. Probable cause for this error is a faulty or uncalibrated double detect module, or a jammed currency in the double detect.1.
Reset the cash dispenser and clear the error. When performing a PURGE or TEST DISPENSE operation the return code will be "0" in the first digit returned by the dispenser. when completing a cassette close function.) to keep it from filling up. Triton 9100 Error Code 148 If these actions have no effect on dispenser operation, replace the dispenser mechanism.
Replace the exit sensor if defective. When the note is stuck in the note transport sensor. 2. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 122 Unexpected note at exit 1. http://u2commerce.com/error-code/triton-atm-error-code-110.html Results: No money is dispensed, screen and receipt display system unavailable.
If the error clears, put the cash dispenser in service. Purge the dispenser using PURGE command. If this does not correct the problem, verify that the paper low sensor is correctly attached to the paper bracket and that the cable between the paper low paper feed assembly