Home > Error Code > Triton Error Code 130

Triton Error Code 130

Contents

Make sure all cables between the note transport and the other units are undamaged and securely seated at their termination point. Enter the full error code number or error code descriptive keyword below Search by Error code Code Type: All HardwareCommunication SEARCH RESULTS BELOW Follow us! No money is dispensed; screen and receipt display system unavailable. 1. Refer to error 522. 526 EJ device busy. this contact form

A temporary fix to this problem may be to set the “low receipt paper” parameter to “in service” so that the terminal software does not read the input from the low Check to make sure that cables connecting the note transport and the CMC module are not damaged. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. This error code indicates that the system has recognized a document intended for the reject vault has reached the note transport sensor. you could try here

Triton Error Code 244

Control your marketing messages remotely. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism. 109 (6Dh) Time-out at Exit It will be necessary to replace the note qualifier. An operating system timeout has occurred.

If the error does not repeat again; complete a live dispense to verify the note diverter moves the currency to the exit position. Find the first occurrence of “116”. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Atm Error Code 3-da000(80) Make sure that the cassettes are installed and locked before performing a test dispense or live transaction. 195 Receipt paper out.

Reset the cash dispenser. Atm Error Codes List If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board, or the main Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. http://www.atmdepot.com/triton-atm-error-codes/ Perform several test dispenses.

If no jam is located; remove the first bill from the cassette. Triton Atm Error Code 101 Otherwise, replace the dispenser.3. Reset the cash dispenser. Inspect the feed path and exit sensor for jammed currency and broken components.

Atm Error Codes List

Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 2. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Triton Error Code 244 Clear all error and purge the dispenser using the purge command.3. Triton Error Code 151 The width sensor may be dirty.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. weblink Dispenser failed to identify the dispenser type installed. If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main If the error persists, replace the dispensing mechanism. Mitsubishi Triton Error Codes

  • Make sure that there is no foreign material in the card slot.
  • Do several test dispense operations. 3.
  • Place all belts on their rollers and gears.
  • Verify that the Reject Vault and one cassette are present in the dispenser mechanism.
  • If these check are not properly completed replace the note qualifier. 326(4Ah)[J] Note feed sensor failure.
  • Test the dispenser by completing several test dispenses. 4.

Test the dispensing mechanism by completing several Test Dispenses. 3. Seat connectors or replace the power supply as needed. 2. Ensure that each cable is securely fastened to its termination point. http://u2commerce.com/error-code/triton-atm-error-code-148.html Inspect electronic journal to dispenser communication cable for damage.

If error persists; replace the dispenser mechanism. 377 Dispenser device error. Triton Error Code 246 Place cassettes in service. 157 Erase command to electronic journal failed 1. Test the dispenser by completing several test dispenses with the test dispense command.

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 105 Insufficient notes to learn from There may be an insufficient number of notes in the cassette

Put the cassettes back into its feed channel. If the error persists replace the dispensing mechanism.chanism. 126 (7Eh) Diverter moved to reject position during dispense Inspect for a note jam at the diverter. Examples of this are two move commands sent one after another or a deliver command that is sent without a previous move command. Triton 9100 Error Code 148 Restart operating system.

Inspect the printer data cable for damage. Restart the cash dispenser. Clear any jammed currency. 2. http://u2commerce.com/error-code/triton-atm-error-code-110.html Inspect for a currency jam at the diverter. 2.

PURGE the dispensing mechanism. Clear the error. Inspect cable from the Electronic Journal to the dispenser to be sure both ends are securely screwed in place. The dispenser sends this status code when a command has been successfully executed.

Inspect the feed path for any jammed notes. Clear terminal error code. This is most often caused by slipping stacker pulleys. 1. If the problem persists; replace the dispenser.

Verify that all cassettes used are in service. 374 Dispenser rejected cheque. Purge the dispenser. Test the dispensing mechanism by completing several test dispenses. If working with an 8100, print a test receipt printer, Verify that the A cassette is in service.

See Error Code 101, 302 or 306 B) Excessive rejects. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 119 (77h) Diverter in dispense position on start of dispense or learn 1. Verify that all DC voltages applied to the printer control board are correct.

Replace the dispenser is the error persists. 359 Dispenser device record error. Generated Sun, 30 Oct 2016 23:23:32 GMT by s_sg2 (squid/3.5.20)