Home > Error Code > Triton Error Code 135

Triton Error Code 135

Contents

If the error persists; replace the dispensing mechanism. 103 (67h) Thickness sensor unstable Enter the diagnostic function and complete the ìlearn note thicknessî command. Inspect the cassette and feed path for jammed notes. Refer to error 522. 524 EJ bad command. Test the dispenser by completing several test dispenses. 4. this contact form

If the voltages are not within tolerance, the cable or power supply may be defective. 4. If these actions have no effect on dispenser operation, replace the dispenser mechanism. Refer to error code 535. 548 Card Reader ñ End sentinel not found. Verify power is applied to the dispenser. 386 Dispenser offline ñ no hoppers. useful source

Triton Atm Error Codes

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Open the printer support bracket and verify that there are no jams in the printer or the paper path. If the problem persists, replace the dispensing mechanism. 135 Feed sensor blocked as reported by status check 1.

  • If the error persists, possible causes of the problem may be the low paper sensor assembly, the docking station, the main board, or cables. 196 Card reader error 1.
  • Check the cable and connections from J7A on the docking station to the SPED board. 210 Dispenser type unknown See Error Code 130 236 Failed to make connection to TCP/IP host
  • If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.
  • If the error does not show again put the cash dispenser into service.
  • Clear all error and purge the dispenser using the purge command. 4.

Inspect electronic journal to dispenser communication cable for damage. Requested amount may exceed the dispensers one time limit. Open the access panels on the note transport and remove any documents that may be in the transport path. Triton Atm Error Code 101 Install the cassette.

Clear all errors and test the dispenser with a live transaction. Triton Atm Error Code 245 Make sure the connectors are seated securely on the main board and on the electronic journal. 2. If the error clears, put the cash dispenser in service. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/ Install the cassette.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Triton Error Code 139 This error code will place the cash dispenser ìOut of Serviceî. If the error clears, put the cash dispenser in service. 6. If error persists; replace the dispenser mechanism. 369 Dispenser device reset.

Triton Atm Error Code 245

Inspect for jammed Currency in the feed path and at the Exit sensor. click to read more Then the original cassette is faulty. Triton Atm Error Codes If the error persists in may be necessary to replace either the cassette or dispensing mechanism. 105 (69h) Insufficient notes to learn from There may be an insufficient number of notes Atm Error Codes List This error code is generated when a cassette is not open and any command other than open cassettes; reset; and close cassettes are sent to the system.

Purge the dispenser. weblink Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 109 Time-out at Exit sensor 1. If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly 5. Make sure that cable is connected at both ends. Triton Atm Error Code 151

Make sure the battery is seated secure in the battery holder. The cables may be defective. 3. Inspect the printer data cable for damage. http://u2commerce.com/error-code/triton-atm-error-code-148.html Clean the card reader assembly with a cleaning card. 3.

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Triton Traverse Error Code 917 Replace the timing wheel or the timing wheel sensors if they are defective. If a belt displays excessive wear or damage you may be able to replace it.

If not, place in service using the Cassette Service menu option.

Test the dispensing mechanism by completing several test dispenses. Refer to error 500. 504 SPED invalid return ID. Check with the processor. 144 No reply from the Electronic Journal Inspect cable to ensure it is securely attached to the Backplane at J4 and at the Electronic Journal. Triton 9100 Error Code 148 Reset the cash dispenser.

Refer to error code 535. 550 Card Reader ñ Card not removed. Clear all errors and test the dispenser with a live transaction. EOT was received as first character after sending a NAK due to a bad response message. http://u2commerce.com/error-code/triton-atm-error-code-110.html Inspect for jammed currency in the transport path between the width sensors and the reject sensor.

If at any time during the following checks; the ìîfaulty note qualifierîî error code recurs. Your cache administrator is webmaster. Telephone line may not be dedicated. (ATM is being used with another devices connected to the line. 2. Baud rate set to high for telephone line conditions.

If error persists; replace the dispenser mechanism. 376 Dispenser multiple device error. Georgia - Las Vegas Web Development by BestHive This page uses frames, but your browser doesn't support them. If the problem persists; replace the dispenser. 50 (32h) Interference recovery Possible static discharge. Make sure all cables are properly connected.

Clean the card reader assembly with a cleaning card. Contact Us online form Error Code Lookup Lookup an error code by number or by the error description. Inspect electronic journal to dispenser communication cable for damage. Time-out is typically 60 seconds. 2.

Time-out waiting for response or carrier was dropped. Inspect the feed path and exit sensor for jammed currency and broken components. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. This is a timing wheel or timing wheel sensor error.. 1.

Inspect the note feeders and note qualifier for damage. Clear all error and purge the dispenser using the purge command.3. Restart operating system.