Home > Error Code > Triton Error Code 210

Triton Error Code 210

Contents

Make sure they are seated at the printer control board and not damaged. 6. If it works with the door open, remove obstruction causing the diverter to contact the vault door. 4. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Enter the Management Functions and configure the bill size. 187 Maximum withdrawal not configured Enter the management functions and configure the “multiple amount” parameter. this contact form

Consider sending the dispenser to repair to have new sensors installed. 38 Blocked exit This status appears if the exit sensor is covered or defective when the dispenser starts. 1. Make sure it is seated at the main board and at the printer control board at CN6. 5. Other components that may cause this error are the main board or the dispensing mechanism. 132 Status reports bad double detect in last dispense 1. Make sure the battery is seated secure in the battery holder. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Atm Error Codes

The exit sensor may be dirty. Make sure the tamper screw is secure to the SPED module. Test the dispenser by completing several test dispenses. If no jam is located, remove the first note from the cassette.

  • Clean as needed with soft brush and vacuum cleaner. 2.
  • If these actions have no effect, replace the dispenser 55 RAM corruption A mechanical failure has occurred.
  • Test the dispenser by completing several test dispenses. 4.
  • Verify that all DC voltages applied to the printer control board are correct.
  • Inspect main board to electronic journal communication cable for damage.
  • Remove any unacceptable currency from the cassette. 2.
  • Refer to Section 5 of the RL5000 Service Manual or the RL5000 Quick Reference Guide for instructions. 2.
  • Purge the dispenser using PURGE command.
  • If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly. 3.

Otherwise, replace the dispensing mechanism. If these actions have no effect, replace the dispensing mechanism. 203 SPED keypad is not replying to main board Status valid only for units with SPED keypad device installed. 1. If the cables are undamaged, the main board or electronic journal may be defective 146 No reply from command to electronic journal 1. Triton Atm Error Code 101 Replenish paper as needed.

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 110 Trailing edge time- out at exit. 1. Check the cable and connections from J7A on the docking station to the SPED board. 210 Dispenser type unknown See Error Code 130 236 Failed to make connection to TCP/IP host Inspect the cable supplying DC power from the power supply to the printer. http://www.atmdepot.com/triton-atm-error-code-151/ Clean and verify the operation of the exit sensor.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Triton Error Code 139 Purge the dispenser with the purge command. If the diverter has excessive binding or appears damaged, replace the dispenser.2. If the cables are undamaged, the main board or electronic journal may be defective 153 Electronic journal mode 1.

Atm Error Codes List

Nautilus Hyosung ATM Machines, Triton ATM Machines, Hantle ATM Machines, and Genmega ATM Machines. Open the Security Cabinet and inspect the cash dispenser for broken parts. Triton Atm Error Codes The cables may be defective. 3. Triton Error Code 244 If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.

Purge the dispenser using the purge command. weblink Release the printer locking screw. Generated Sun, 30 Oct 2016 18:02:51 GMT by s_wx1199 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 128 Error in reply from the dispenser mechanism 1. Triton Error Code 151

Inspect the feed path and Feed sensors for jammed currency and broken components. The dispenser will shut down, possibly resulting in trailing notes stopping in the path. 1. If these actions have no effect on dispenser operation, replace the dispenser mechanism. http://u2commerce.com/error-code/triton-atm-error-code-148.html State by verify if this is associated with error code 151.

Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Triton 9100 Error Code 148 Verify that all access panels are closed and secured. Test the dispenser by completing several test dispenses.

If so, work to resolve error code 151. 1.

Then it will go “out of service”” for and error code 195 “out of paper”. 185 Telephone number not configured Enter Management Functions and configure the telephone number. 186 Bill Size If these actions have no effect on dispenser operation, replace the dispenser mechanism. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. Triton Error Code 616 Look up the definition on the Hardware Status listing. 4.

If the status clears and the return code are normal place the cash dispenser in service. Inspect the dispensing mechanism for jammed currency at the diverter. Clear the error. 5. http://u2commerce.com/error-code/triton-atm-error-code-110.html Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

Seat connectors or replace the power supply as needed. 2. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5 If the cables are undamaged Leave a Reply Cancel reply Your email address will not be published. Check the incoming power and dispenser mechanism for proper grounding. 2.

Purge the dispenser. If the error persists, replace the SPED keypad module. 205 SPED keypad reported tamper condition Status valid only for units with SPED keypad device installed. Clear the error. Reset the cash dispenser.

If excessive rejects are suspected, see corrective action for Error Code 48. 3. Inspect for jammed currency in the transport path between the width sensors and the reject sensor. If a belt displays excessive wear or damage you may be able to replace it. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. Journal transactions also include cassette close, trial closes, and other admin functions. If the cables are undamaged, the main board or electronic journal may be defective 149 Read from electronic journal failed 1. Enter your name and a valid email address and we'll deliver our Free 17 Page PDF Guide on how to profit from the ATM business right to your inbox. 17 Page

The cables may be defective. 3. Probable cause for this error is a faulty or uncalibrated double detect module, or a jammed currency in the double detect.1. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.

The result will provide the cause of the error and the recommended action. Inspect electronic journal to dispenser communication cable for damage.