Home > Error Code > Triton Error Code 42

Triton Error Code 42

Contents

Verify that the identity of each cassette can be read through read cassette ID function (See the 5000 Cash Dispenser Configuration Manual). It will be display as the hexadecimal number ì30î when running the dispenser with the NMD test software. 301 (31h)[1] Low level in cassette. Access the management function diagnostics menus to verify the operational error code of dispenser mechanism sensors. If error persists; replace the main board assembly. 558 System sync error. this contact form

Cassettes with no identity must be injected with a new cassette ID (See the 5000 Cash Dispenser Configuration Manual). Complete several test dispenses. Restart the cash dispenser. Make sure it is connected to CN1 on the printer control board. directory

Atm Error Codes List

Test the dispenser by completing several test dispenses. 4. Replace cassette or Inject New Cassette ID. 500 SPED Read Error. Clean as needed with compressed air.

  1. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.
  2. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3.
  3. Clear terminal error code.
  4. Purge the dispensing mechanism with the PURGE command from the DIAGNOSTICS function.
  5. The width sensor may be dirty.
  6. Make sure it is seated at the main board and at the printer control board at CN6. 5.

The width sensor may be dirty. Inspect the feed path for currency that is stuck together or jammed. Ensure the ATM is mounted on a hard steady surface. Atm Error Codes 072 Replace SPED if error persists. 501 SPED invalid return record.

If these actions have no effect, replace the dispenser 55 RAM corruption A mechanical failure has occurred. Triton Error Code 244 This error code will be generated when the following conditions occur: 1. This is done to indicate that the power has been off. http://www.atmdepot.com/triton-atm-error-codes/ Clear any jammed currency. 2.

If the operation is normal; you may put the cash dispenser in service. Mitsubishi Triton Error Codes P0421 Warm-Up Catalyst Efficiency below threshold (Bank 1). If the cables are undamaged, the main board or electronic journal may be defective 163 Terminal did not answer. If this does not correct the problem, verify that the paper low sensor is correctly attached to the paper bracket and that the cable between the paper low paper feed assembly

Triton Error Code 244

Release the printer locking screw. NMD dispenser allows for only one of each cassette ID to be installed. Atm Error Codes List This is the status after a normal dispense. 33 (21h) Feed failure This error is usually associated with an empty cassette or currency that is in UNFIT condition. Triton Error Code 151 Ensure they are marked as audited. 3.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. weblink Make sure the battery is seated secure in the battery holder. 2. This Error Code is valid for units with SPED keypad device installed. All Rights Reserved.

This page uses frames, but your browser doesn't support them. Atm Error Code 3-da000(80)

Inspect the dispensing mechanism for jammed currency at the exit sensor. Ensure that each cable is securely fastened to its termination point. Clear all errors and test the dispenser by completing several TEST DISPENSES. http://u2commerce.com/error-code/triton-atm-error-code-148.html A defective cassette may also cause this problem. 333(51h)[Q] Reject vault full.

Clean the exit sensor using a soft brush and a vacuum cleaner. Triton Error Code 139 If the sensor is not operating normally; replace the note transport module. 318(42h)[B] Too many notes requested. If the error persists replace the dispensing mechanism.

All cassettes have reached low cash level.

Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 125 Initial status check failed 1. Clear all errors and test the dispenser with a live transaction. Triton Atm Error Code 101 This error code occurs when the message received by the dispenser is incorrect.

The Triton Connect Host Computer generates this error when a terminal does not return a call to the Triton Connect Host Computer as requested. Seat connectors or replace the power supply as needed. 2. Clean and verify the operation of the exit sensor. http://u2commerce.com/error-code/triton-atm-error-code-110.html If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.

If two or more of the same type cassette are installed; inject a new cassette ID into one of the cassettes that is different from the other cassette. 101 (65h) 2-second If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Inspect the cables connected to CN2, CN3, CN4, and CN5. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 113 (71h) Timeout waiting for trailing edge at reject 1.

Refill the cassette as needed. 2. Examine the timing wheel for physical defect. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism. Inspect jumper block LK5 on the dispenser main board.