Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Instead, save the journal to an external USB storage device or download to Triton Connect. Check to make sure that cables connecting the note transport and the CMC module are not damaged. Verify that the Reject Vault and one cassette are present in the dispenser mechanism. this contact form
Remove and fill the affected cassette using normal procedures. Clear all error and purge the dispenser using the purge command.3. Retry the test operation and request fifty or fewer notes. 319(43h)[C] Jam in note transport. Restart operating system. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/
Make sure that there is no foreign material in the card slot. Replace the dispensing mechanism. 54 Operation time-out 1. Clear any jammed currency.2. Clear terminal error code.
If the status clears and the return code are normal place the cash dispenser in service. It is usually caused by attempting to dispense currency that is unacceptable or currency that has not been properly prepared. 1. If replacing the modem does not correct the problem; replace the main board. 138 Print failure while printing to the receipt printer. Mitsubishi Triton Error Codes Replace the dispenser. 47 (2Fh) Note missing at double detect Inspect the feed path for notes jammed.
Great rates with no hidden fees; ATM Merchant Systems offers long-term low processing rates you can count on paired with outstanding service and support you can trust. Atm Error Codes List If the cables are undamaged, the main board or electronic journal may be defective 148 Write to electronic journal failed Most probable cause, the electronic journal is full. Restart ATM. Verify that all access panels are closed and secured.
If it is necessary to check continuity of the cable assembly,refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Triton Atm Error Code 101 Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Remove the cassette and inspect the dispenser’s feed path for jammed currency and other debris in the double detect assembly. Either the VEPP was changed or the software was reloaded, such as when you do a VEPP upgrade, or if the VEPP was changed. 2.
Clear the error. 5. Purge the dispenser with the purge command. Triton Error Code 244 If the error clears; put the cash dispenser in service. 4. Triton Error Code 151 Inspect the currency for excessive wear.
Purge the dispensing mechanism with the PURGE command from the DIAGNOSTICS function. weblink If the error persists; possible causes of the problem may be the low paper sensor assembly; the docking station; the main board; or cables. Open the Printer Bracket and verify that there are no jams in the printer or the paper path. The cables may be defective. 3. Atm Error Code 3-da000(80)
Reset the error. Examples of this are two move commands sent one after another or a deliver command that is sent without a previous move command. Restart operating system. http://u2commerce.com/error-code/triton-atm-error-code-148.html If the error clears, put the cash dispenser in service. 4.
Clear the error. Triton Error Code 246 If no jam is located, remove the first note from the cassette. Replenish the paper.
If it works then, the cassettes may not staying locked in the cassettes. Reset the error code. Inspect the dispenser to make sure all belts are on track and in good physical condition. Triton 9100 Error Code 148 Inspect the cassette and feed path for notes that are stuck together or jammed.
If a cassette is not responding it may be necessary to inject a new identity into the cassette by completing the inject new cassette ID command. This error code is reported by the dispensing mechanism when a document is jammed in the throat sensor during a live dispenses or when a reset is performed. Test the dispenser by completing several test dispenses. 4. http://u2commerce.com/error-code/triton-atm-error-code-110.html This occurs when the last cassette has been taken out of service.
Purge the dispenser using the purge command. 3. Verify the blue lever on the left side of the printer in the print position. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Purge the dispenser with the purge command under diagnostics.
Make sure it is seated at the main board and at the printer control board at CN6. 5. If replacing the modem does not correct the problem, replace the main board. 138 Printer failed while printing to the receipt printer 1. Inspect the feed path for jammed notes.