The most likely cause is internal communication problems within the dispenser. Outside interference may cause it (neon signs, lights). Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Check the cable and connections from J7A on the docking station to the SPED board. 210 Dispenser type unknown See Error Code 130 236 Failed to make connection to TCP/IP host this contact form
Can only be cleared in Diagnostics>Keypad>Clear Tamper. If the error clears; put the cash dispenser in service. 5. It will be display as the hexadecimal number ì30î when running the dispenser with the NMD test software. 301 (31h) Low level in cassette. If the problem persists; replace the dispenser. 50 (32h) Interference recovery Possible static discharge. https://www.nasatm.com/error_codes/code/565/
Replenish paper as needed. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. If left unchecked, it could result in total and permanent loss of all data and inoperability of the storage media and/or PC device. Replace the dispenser is the error persists. 368 Dispenser cannot dispense the request.
If error persists; replace the dispenser mechanism. 371 Dispenser SDD com error header-trailer. Verify that version of Mini-Bank Software matches host processor. If the voltages are not within tolerance, the cable or power supply may be defective. 4. If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust).
Replace the dispenser. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. This error code causes an ìOut of Serviceî condition. http://buymaleextra.us/how-to-fix-triton-error-code-565-errors-in-windows.html Specific meaning or definition can vary between the different processors.
If the problem persists; replace the dispenser. 36 24h) Mistracked note at exit Inspect the cassette and feed path for jammed notes. Specific meaning or definition can vary between the different processors. Remove any unacceptable currency from the cassette. 2. Shorted (power to ground) harness.
This error will not put the cash dispenser ìOut of Serviceî. Inspect the note transport and delivery throat make sure all belts are on track and there are no documents jammed in the transport or exit areas. Atm Error Codes List Replace the dispenser. 53 (35h) EPROM error A mechanical failure has occurred. Reset the cash dispenser and clear the error.
Time-out is typically 60 seconds. 3. weblink Hantle formerly . If the error is repeated; proceed to the next paragraph. Cracked or broken clips should be replaced 4.
Restart the operating system. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. If these check are not properly completed replace the note qualifier. 326(4Ah)[J] Note feed sensor failure. http://u2commerce.com/error-code/triton-atm-error-code-148.html Complete several test dispenses.
Clear terminal error code. 385 Dispenser offline; no reject vault and not hoppers. There should be no jumpers installed. 2. Refer to error 522. 525 EJ invalid ID.
The modem may be defective. 165 Electronic journal not present 1. Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). Restart the operating system. Inspect all communication cables to make sure they are not damaged and are properly connect to their termination points.
If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Check the cable and connections from the docking station to the SPED board. The maximum withdrawal cannot exceed 50 time the denomination of the bill size in the cassette. 188 PIN working key not configured Enter the management functions and configure (download) the working http://u2commerce.com/error-code/triton-atm-error-code-110.html The hoppers are not detected.
If the error persists; replace the dispensing mechanism. 103 (67h) Thickness sensor unstable Enter the diagnostic function and complete the ìlearn note thicknessî command. Request has been sent. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Clear the error.
Used up all radial attempts and got No Dial Tone for each attempt. 2. Refer to error 500. 506 SPED invalid request.