Home > Error Code > Triton Error Code 616

Triton Error Code 616

Contents

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 103 Thickness sensor unstable Enter the diagnostic function and complete the “learn note thickness” command. Make sure that the exit sensor is clean and operation correctly. 3. Seat connectors or replace the power supply as needed. 2. Verify the physical presence of each cassette. this contact form

Place all belts on their respective rollers and gears. If the error recurs, a faulty cassette, note feeder or CMC module may be cause the problem. If the voltages are not within tolerance, you may need to replace the cable or power supply. However, actions to fill the cassette should be taken as soon as possible. https://www.nasatm.com/error_codes/code/616/

Triton Atm Error Code 33

Carrier was lost before receiving EOT. If so, work to resolve error code 151. 1. Error Code: 300(30h)[0] Description: Successful Command Recommended Action: The dispenser sends this error code when a command has been successfully executed. Clear any jammed currency. 2.

Can only be cleared in Diagnostics>Keypad>Clear Tamper. If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly. 3. Recommended Action: This status is generated if the double detect is unable to calibrate. Triton Error Code 236 Inspect electronic journal to dispenser communication cable for damage.

Clean the exit sensor using a soft brush and a vacuum cleaner. Triton Error Codes Error Code: 187 Description: Maximum withdrawal not configured. Remove any unacceptable currency from the cassette. 2. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.

If the cables are undamaged, the main board or electronic journal may be defective 146 No reply from command to electronic journal 1. Triton Error Code 101 Make sure the connectors are seated securely on the main board and on the electronic journal. 4. It the status clears, place the cash dispenser in service. Clean as needed with compressed air.

  • PURGE the dispensing mechanism.
  • Check the incoming power and dispenser mechanism for proper grounding. 2.
  • Make sure the diverter is not jammed.
  • Error Code: 303(33h)[3] Description: Lifts are down.
  • If the problem persists, replace the dispensing mechanism.
  • Error Code: 357 Description: Dispenser data size error.
  • Use a soft brush and vacuum cleaner to clean the exit sensor. 4.

Triton Error Codes

Clean the sensors a needed. 2. http://atmequipment.com/s.nl/it.I/id.20/.f Recommended Action: Error code valid only for units with SPED keypad device installed. Triton Atm Error Code 33 Clean the exit sensor using a soft brush and a vacuum cleaner. Triton Error Code 244 Recommended Action: Restart the operating system.

Recommended Action: See the recommended action for error code 128 Error Code: 134 Description: Exit blocked as reported by error code check. weblink If the journal becomes, full the only way it can be cleared and have a copy of it records is to print to the receipt printer or download the journal to Recommended Action: Open the Security Cabinet and inspect the cash dispenser for broken parts. If the error persists in may be necessary to replace either the cassette or dispensing mechanism. Triton Error Code 151

Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean. Inspect the feed path and Feed sensors for jammed currency and broken components. Inspect all communication cables to make sure they are not damaged and are properly connect to their termination points. http://u2commerce.com/error-code/triton-atm-error-code-148.html b.

Other possible causes may be a defective modem or main board Error Code: 193 Description: The baud rate setting for electronic journal failed. Mitsubishi Triton Error Codes If the problem persists, replace the dispensing mechanism. 135 Feed sensor blocked as reported by status check 1. Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

Recommended Action: Enter the management function and configure the terminal ID correctly.

Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Replace the dispenser is the error persists. Error Code: 206 Description: SPED keypad could not perform a successful command within SPED MAX_ATTEMPTS tries. Triton Error Code 246 Perform a live transaction.

Error Code: 103 (67h) Description: Thickness sensor unstable Recommended Action: Enter the diagnostic function and complete the learn note thickness command. Error Code: 112 (70h) Description: Timeout waiting for leading edge at reject Recommended Action: A note that was expected to be seen by the reject sensor was not detected by the If this does not correct the problem, verify that the paper low sensor is correctly attached to the paper bracket and it is connected to the printer controller PCB. http://u2commerce.com/error-code/triton-atm-error-code-110.html Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser.

If the error returns, inspect the stacker pulleys to ensure they are not slipping. 4. Recommended Action: Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Verify that all access panels are closed and secured. Recommended Action: Replenish the paper.

Make sure that the exit sensor is clean and operation correctly.3. If these actions have no effect, replace the dispenser. Purge the dispenser using the purge command. Error Code: 142 Description: Dispenser returns bad command error.

Please try the request again.