Home > Error Code > Triton Error Codes 130

Triton Error Codes 130

Contents

Clear all errors and test the dispenser by completing several TEST DISPENSES. If any sensor is out of its calibration limits; clean all of the sensors and attempt to do a transaction. Inspect the note diverter in the note transport module. Inspect for jammed currency in the transport path between the width sensors and the reject sensor. http://u2commerce.com/error-code/triton-atm-error-codes-pdf.html

Test the dispenser by completing several test dispenses. 4. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Make sure it is seated at the main board and at the printer control board at CN6. 5. Reset the error. https://prineta.com/atms/docs/atm-error-codes-triton-machines/

Triton Atm Error Code

An operating system timeout has occurred. Inspect main board to electronic journal communication cable for damage. This error may occur anytime that a cassette is removed from the cash dispenser with the AC Power ON. Purge the dispenser with the purge command under diagnostics.

Remove and empty the reject vault. This Error Code is valid for units with SPED keypad device installed. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism. 109 (6Dh) Time-out at Exit Mitsubishi Triton Error Codes If no jam is located, remove the first note from the cassette.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Triton Error Code 244 It is usually caused by attempting to dispense currency that is unacceptable or currency that has not been properly prepared. 1. Seat connectors or replace the power supply as needed. 2. try this Otherwise, replace the dispensing mechanism.

Inspect the dispensing mechanism for of damaged components or broken wires. 2. Atm Error Code 3-da000(80) Inspect electronic journal to dispenser communication cable for damage. A normal return code for this test dispense operation is ì4 1 1 1 1? Restart operating system.

  • Refer to error 500. 503 SPED invalid command.
  • This error code is generated by the dispensing mechanism when the calibration value for at least one of the sensors in any of the note feeders has exceeded the upper limits
  • Test the TDM-100 by completing several Test Dispenses.

Triton Error Code 244

Verify the blue lever on the left side of the printer in the print position. Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends. Triton Atm Error Code Make sure it is seated at the main board at J15 and at the printer control board at CN6. Atm Error Codes List Refer to error code 535. 552 Card Reader ñ Device received invalid request.

Remove any jammed currency. 2. weblink If the cables are undamaged, the main board or electronic journal may be defective8100, 9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT2000151Electronic journal fullThe electronic journal on 8-bit machines (9600, Clear all errors and test the dispenser by completing several TEST DISPENSES. If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism. Triton Error Code 151

Inspect the cables connected to CN2, CN3, CN4, and CN5. Overcome space limitations while engaging customers with multiple marketing presentations utilizing videos, menu screens, avatars, widgets all on the same monitor; ultimately maximizing your retail footprint. If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly. 3. navigate here Restart the cash dispenser.

Check the cassettes. Triton Atm Error Code 101 Attempting to operate the cash dispenser without the reject vault will normally cause it to go to an ìOut of Serviceî condition. The transaction will be completed with the customersí receipt indicating the amount of cash actually received.

Time-out is typically 60 seconds. 2.

Test the dispenser by completing several test dispenses with the test dispense command. Verify that all DC voltages applied to the printer control board are correct. Triton Connect error. Triton Error Code 246 Test the dispensing mechanism by completing several test dispenses.

If the voltages are not within tolerance, the cable or power supply may be defective. 4. Remove each note feeder module from the dispensing mechanism and clean their associated empty; pressure and exit sensors with clean compressed air. Restart operating system. his comment is here This status occurs when a note is detected by the exit sensor when it should not have been.

Seat connectors or replace the power supply as needed. 2. The reject vault should be emptied as soon as possible in order to avoid an ìOut of Serviceî condition that occurs when the number of reject events reaches 50. Choose Clear Journal. State by verify if this is associated with error code 151.

ATMs with NMD or Mini Mech dispensers require electronic journals with part number that start with “9600” or “09600”. 2. If so, work to resolve error code 151. 1. If the error does not show again put the cash dispenser back into service. Perform required audit of the cash.

Verify that all DC voltages applied to the printer control board are correct. Replace the power supply or dispenser DC power if either is defective.3. Open the printer and verify that there are no jams in the printer or the paper path. Clean as needed with soft brush and vacuum cleaner. 2.

Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. If these actions have no effect on dispenser operation, replace the dispenser mechanism. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.