Home > Error Code > Triton Error Codes 144

Triton Error Codes 144

Contents

Remove jammed currency. 2. If error persists; replace the dispenser mechanism. 387 Dispenser offline ñ error validating configuration. Refer to error code 535. 539 Card Reader ñ Invalid track. Test the dispenser by completing several test dispenses. 3. http://u2commerce.com/error-code/triton-atm-error-codes-pdf.html

Inspect the note transport for damage and verify that all connectors are plugged into their respective receptacles. Home 1-866-787- 4866 | e-Mail | About | Contact Us | Login Products News Services & Support Partner Programs Service & Support Training Programs Warranty Programs Warranty Registration Legacy Products If EOT is received on subsequent attempts; then Error Code 1 is reported. (If problem persists call Your Service Provider or Triton Tech Support). 15 Timed out waiting for EOT See Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. read the full info here

Atm Error Codes List

If the cables are undamaged, the main board or electronic journal may be defective 150 Status command to journal failed 1. If the problem persists; remove the main board and replace the modem. Baud rate set to high for telephone line conditions. Refer to error code 535. 545 Card Reader ñ LRC error.

  1. See the recommended action for Error Code 128. 130 Command not acknowledged by the dispenser mechanism.
  2. Otherwise; replace the dispensing mechanism. 110 (6Eh) Trailing edge time-out at exit. 1.
  3. Refer to error 522. 530 EJ EXT error.
  4. Verify that there are no documents jammed in the note diverter area.
  5. Otherwise; replace the dispenser. 38 (26h) Blocked Exit Exit sensor blocked or open circuit.
  6. If the error code returns; replace the note transport module. 330(4Eh)[N] Communication timeout This error is reported when the transmission of each one of the characters in the command string is
  7. Generated Wed, 27 Jul 2016 11:01:22 GMT by s_rh7 (squid/3.5.20)
  8. Use a soft brush and vacuum cleaner to clean the exit sensor. 4.
  9. Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is

Remove and empty the reject vault. b. Inspect for jammed currency in the feed path and at the Exit sensor. Triton Error Code 244 Purge the dispenser using purge command.

Purge the dispenser. Refer to error code 535. 538 Card Reader ñ Reader type error. This error code is returned by the dispenser when the number of notes in one or more of the cassettes is below a preset level; indicating the low level sensor in On all models other then 96XX, Release the printer locking screw.

Place all belts on their respective rollers and gears. Atm Error Code 68 If the cash dispenser operates normally put it in service. Test the dispensing mechanism by completing several test dispenses. Inspect the feed path for notes stuck together or jammed.

Atm Error Code 3-da000(80)

Cracked or broken clips should be replaced 4. http://atmms.com/ Clear the error. Atm Error Codes List Verify all connectors to the dispenser mechanism. Atm Error Code 3-da001 Time-out waiting for response or carrier was dropped.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. check over here Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Place all belts on their rollers and gears. Atm Response Code 072

This Error code will occur only in Cash Dispensers running ACS terminal software. Place all belts on their rollers and gears. See error code 557. 560 Unknown device error. his comment is here Complete a Test Dispense.

Replace the dispenser is the error persists. 365 Dispenser BCC error. Triton Error Code 151 If the problem persists; replace the dispenser. If the status clears and the return code are normal place the cash dispenser in service.

Perform a test dispense.

Replace SPED if error persists. 501 SPED invalid return record. If it is necessary, check continuity of the cable assembly. 5. Make sure it is connected to CN1 on the printer control board. Sbi Atm Response Code 070 Means Make sure all connectors attached to the CMC are seated in their receptacles.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Open the printer support bracket and verify that there are no jams in the printer or the paper path. Test the dispensing mechanism by completing several test dispenses. weblink Install the Reject Vault.

Verify that all DC voltages applied to the printer control board are correct.