Home > Error Code > Triton Ft 5000 Error Codes

Triton Ft 5000 Error Codes

Contents

Restart the operating system. Buy the Full Version triton-errorcodes by Pierre Semaan240 viewsEmbedDownloadRead on Scribd mobile: iPhone, iPad and Android.Copyright: Attribution Non-Commercial (BY-NC)List price: $0.00Download as PDF, TXT or read online from ScribdFlag for inappropriate Reset the cash dispenser. Inspect the cassette and feed path for jammed notes. this contact form

It is not displayed directly to the operator or customer. All rights reserved. Remove any documents from the tote transport. When troubleshooting the 8100, 9100, RL and RT be aware that the electronic journal is built into the main board of the dispenser. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Triton Atm Error Code 148

Inspect the dispensing mechanism for of damaged components or broken wires. 2. This error code is generated when there is a sensor error in one or more of the note feeders or when there is a document jammed in the note feeder exit Otherwise, replace the dispenser. 39 Too many notes Clean the all sensors.

  • Inspect the cassette and feed path for notes that are stuck together or jammed.
  • Clear the error.
  • Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct.
  • Refill the cassette as needed. 2.

Replace the dispenser is the error persists. 368 Dispenser cannot dispense the request. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Mitsubishi Triton Error Codes Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 103 Thickness sensor unstable Enter the diagnostic function and complete the “learn note thickness” command.

Complete the test receipt printer function to determine which if any of the cassettes are not responding. Triton Error Code 244 If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Inspect for jammed Currency in the feed path and at the Exit sensor. http://www.atmdepot.com/triton-atm-error-codes/ Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 117 Timeout waiting for note to divert   118 Exit sensor blocked on start of dispense or

Inspect the cable supplying DC power from the power supply to the printer. Triton Traverse Error Code 917 If the error clears; put the cash dispenser in service. 5. Dispenser failed to identify the dispenser type installed. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5 If the cables are undamaged

Triton Error Code 244

If cash dispenser operates normally when performing the test dispense function; put the cash dispenser in service. http://www.atmnetwork.net/support/troubleshooting/TritonRL5000.asp PURGE the dispensing mechanism. Triton Atm Error Code 148 If all sensors are operation correctly; and the error persists; replace the replace the dispenser. 42 (2Ah) Transport Error This is a timing wheel or timing wheel sensor error. 1. Triton Atm Error Code 33 The recommended capacity is 1850 documents.

Inspect the cable supplying DC power from the power supply to the printer. http://u2commerce.com/error-code/triton-atm-error-codes-pdf.html If these check are not properly completed replace the note qualifier. 326(4Ah)[J] Note feed sensor failure. Verify the blue lever on the left side of the printer in the print position. 3. Release the printer locking screw. Triton Error Code 151

Complete several live dispenses to ensure the dispenser is working correctly. If no jam is located, remove the first note from the cassette. If working with an 8100, print a test receipt printer, Verify that the A cassette is in service. navigate here Make sure all access panels are closed.

If the inject cassette ID function works on a different cassette. Triton Atm Error Code 101 Refer to error 522. 533 EJ BCC error. Attempting to operate the cash dispenser without the reject vault will normally cause it to go to an ìOut of Serviceî condition.

Reset the cash dispenser.

If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main Refer to error code 535. 552 Card Reader ñ Device received invalid request. NMD dispenser allows for only one of each cassette ID to be installed. Triton Error Code 246 Then the original cassette is faulty.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 3. Replace the dispenser. his comment is here Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 116 Motor Fault 1.

Purge then test dispense. Refer to error 500. 515 SPED device attention stuck. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Refer to error 522. 532 EJ STX error.

Replace the dispenser if it is broken. Make sure they are not overfilled. Clear terminal error code. If the error persists; replace the SPED keypad module. 206 SPED could not perform a successful command within SPED_MAX_ATTEMPTS tries Error code valid only for units with SPED keypad device installed.

Restart the operating system. Other components that may cause this error are the main board or the dispensing mechanism. 134 Exit blocked as reported by status check 1. Inspect the dispensing mechanism for jammed currency at the exit sensor. Clear the error. 3.

Refer to error code 535. 546 Card Reader ñ No data. If the sensor appears okay and the cable is seated properly; replace the Printer Controller Board. 185 Phone number not configured Enter management functions and configure the primary phone number 186 If the cables are undamaged, the main board or electronic journal may be defective 166 Bad dispense 1. Contact Us online form Error Code Lookup Lookup an error code by number or by the error description.

Clear terminal error code. Inspect for jammed currency in the transport path between the width sensors and the reject sensor. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. This error code is returned by the dispenser when the number of notes in one or more of the cassettes is below a preset level; indicating the low level sensor in

The exit sensor may be dirty. Test the dispenser by completing several test dispenses. 5. Inspect the printer data cable for damage. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.