Verify that the Reject Vault and one cassette are present in the dispenser mechanism. Close vault door. 800.498.5795 New! If the error clears, put the cash dispenser in service. 5. Reset the cash dispenser. http://u2commerce.com/error-code/triton-atm-error-codes-pdf.html
Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. Test the dispensing mechanism by completing several test dispenses. 4. Remove any jammed currency. 2. If the error clears put the Cash Dispenser into service. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/
Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Inspect the cable supplying DC power from the power supply to the printer. Restart the cash dispenser. No characters were received.
Clear the error. Clear the error. Refer to error code 535. 552 Card Reader ñ Device received invalid request. Mitsubishi Triton Error Codes Make sure the connectors are seated securely on the main board and on the electronic journal. 4.
If the currency is in “”fit”” condition and the error condition persists, consider replacing the note cassette or the dispensing mechanism. Inspect electronic journal to dispenser communication cable for damage. Make sure the reject vault is installed correctly. Reset the cash dispenser and clear the error.
If error persists; replace the SPED module. 565 Cabinet door open. Triton Atm Error Code 101 Verify the blue lever on the left side of the printer in the print position. 3. Remove any documents from the tote transport. Make sure it is seated at the main board and at the printer control board at CN6. 5.
Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. useful source Restart the operating system. Triton Error Code 244 Purge the dispenser using the purge command. Triton Atm Error Code 33 Make sure the connectors are seated securely on the main board and on the electronic journal. 4.
Configuration jumpers may have been changed. weblink Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. Release the printer locking screw. Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette. Triton Error Code 151
This is a Triton Connect error. If a cassette cannot be injected with a new ID; verify that the cable between the top feed channel and the CMC is in good condition and connected at both ends. If it is necessary to check continuity of the cable assembly,refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. navigate here Verify the blue lever on the left side of the printer in the print position. 3.
Purge the dispenser. Triton Traverse Error Code 917 If the error code has been cleared; the cash dispenser can be put back in service. Clear all errors and test the dispenser with a live transaction.
b. Check dip switch settings on the printer controller board to verify they are set correctly. This error code may indicate a power loss/firmware restart has occurred at the dispenser controller and no information could be retrieved. Triton Error Code 246 This status is reported if the exit sensor is covered for a longer that allowed time for the current notes.1 Inspect the note transport and delivery throat make sure all belts
Verify that the cable that connects the double detect module to the CMC module is undamaged and connected at both ends. If the requested amount cannot be dispensed; the customer will receive the cash that can be dispensed. Inspect the reject vault present sensor visually for proper operation. his comment is here Otherwise, replace the dispenser.Note, if this occurs on a Mini Mech, only during a multi note dispense, the exit sensors may have become weak.
Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is Inspect for jammed Currency in the feed path and at the Exit sensor. This error code will cause an ìOut of Serviceî condition. Complete several Test Dispenses to verify correct operation.
If the error persists, replace the dispenser. 46 Exit quantified This status appears when the count at the exit is greater than the number of documents requested.1.