If it is necessary to check continuity of the cable assembly, refer to Appendix B for pin out of the cable assembly. 3. If these actions have no effect on dispenser operation; replace the dispenser mechanism. 128 Error in reply from the dispenser mechanism Inspect cable from the Backplane to the Electronic Journal to Contact Us online form Error Code Lookup Lookup an error code by number or by the error description. Inspect electronic journal to dispenser communication cable for damage. this contact form
Perform a live transaction. Clean the dirty sensor; or replace the note transport as needed. Inspect the incoming power and check for proper grounding 51 (33h) Suspect exit accountancy A mechanical failure has occurred. Reset the cash dispenser by turning OFF the AC power switch for a few seconds and switching it back ON.
JarrettATM1 6,291 views 3:22 Orwellian Biometric ATM machines - Duration: 4:49. Clear terminal error code. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. If the problem remains after reloading the cassette; replace the cassette; the denomination extension; or the note feeder controller associated with the cassette causing the problem. 351(63h)[c] Module needs service.
Clear all errors and test the dispenser by completing several TEST DISPENSES. This is most often caused by slipping stacker pulleys. 1. Please try again later. Triton Atm Error Code 101 If the error persists; replace the dispensing mechanism. 104 (68h) Unable to clear width sensor.
Make sure the ribbon cable from the docking station go the card reader is fastened at both ends of the cable and the orientation of the cable is correct. Triton 9100 Error Codes Clear terminal error code. Clear the error. If these actions have no effect, replace the dispenser. 44 Bad Roller Profile This status is generated if the double detect is unable to calibrate.
This error code is generated when the reject vault is not present or not properly installed. Mitsubishi Triton Error Codes If the problem persists; replace the dispenser. 55 (37h) Ram corruption A mechanical failure has occurred. Purge the dispenser using the purge command. The next entry, below 116, is the Hardware Status.
All Rights Reserved. their explanation Use the diagnostic functions or NMD test software to determine if a note feeder has a faulty or dirty sensor. Triton Error Code 244 Make sure they are seated at the printer control board and not damaged. 6. Triton Error Code 151 Restart the cash dispenser.
Clear all errors and test the dispenser by completing several TEST DISPENSES. http://u2commerce.com/error-code/triton-error-codes-135.html Replace the dispenser is the error persists. 365 Dispenser BCC error. This is error code will set an ìOut of Serviceî condition. Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is Atm Error Codes List
If LOW CURRENCY CHECKING is enabled; and the terminal dispenses all of its cash; and the cassette has not been filled with enough cash to position the packer plate far enough Release the printer locking screw. Use the reject channel error code function to verify the operation of the sensors on the note transport module. http://u2commerce.com/error-code/triton-atm-error-codes-pdf.html If a receipt is not printed during the printer self test; then either the Printer or Printer Control Board or its interconnected wiring are defective.
The Triton Connect Host Computer generates this error when a terminal does not return a call to the Triton Connect Host Computer as requested. Triton Traverse Error Code 917 If the cables are undamaged, the main board or electronic journal may be defective 149 Read from electronic journal failed 1. Make sure that the ribbon cable from the docking station to the low paper sensor assembly is fastened at both ends of the cable and the orientation of the cable is
If these actions have no effect on dispenser operation, replace the dispenser mechanism. If the error clears; put the cash dispenser in service. 6. Make sure the battery is seated secure in the battery holder. Triton Error Code 246 Make sure the connectors are seated securely on the main board and on the electronic journal. 2.
Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. 3. This problem may be caused by incompatibilities between terminal software and dispensing mechanism software. Next try a live dispense (note, you can not fully test this dispenser for this error without doing live dispenses). his comment is here If the cables are undamaged, the main board or electronic journal may be defective 153 Electronic journal mode 1.
Clear the error. Try to inject an ID into another cassette. Test the dispensing mechanism by completing several test dispenses. 4. Clean the sensors in the note transport a needed.
Clear terminal error code. If the error recurs; change the note feeder for the affected channel. 320(44h)[D] Reject cassette almost full. Replace the dispenser is the error persists. 362 Dispenser device write error. The dispenser sends this status code when a command has been successfully executed.
The result will provide the cause of the error and the recommended action. Clear terminal error code. Inspect the dispensing mechanism for of damaged components or broken wires. 2. Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable.
If these actions have no effect, replace the dispenser. 51 Accountancy error A mechanical failure has occurred. Inspect for jammed currency in the feed path and at the Exit sensor. Replace the dispensing mechanism. 53 EPROM error A mechanical failure has occurred. This is a Triton Connect error. 1.
Error code 320 will not put the cash dispenser ìOut of Service. The Triton Connect Host Computer generates this error when a terminal does not make a call to the Triton Connect Host Computer as requested. This error code is generated by the dispensing mechanism when the calibration value for at least one of the sensors in any of the note feeders has exceeded the upper limits Verify the blue lever on the left side of the printer in the print position. 3.