Home > Error Codes > Trane Xl80 Error Codes

Trane Xl80 Error Codes


Is this normal and is it ok to keep running it? Ask Your Own HVAC Question Customer: replied5 years ago. Recommended Action: Check your thermostat and heating unit to assure that they are both plugged in. Remove the furnace door panel and locate what I just described. Check This Out

He did not know I was listening. grayfurnaceman 17,759 views 6:06 How To Troubleshoot Your Furnace - Duration: 27:55. If I found the rigfht thing, they have little stems sticking out of them. Trane furnace blinking red light troubleshooting guides are located inside the unit manual or online. http://www.furnacereviews.net/trane-furnace-blinking-red-light.html

Trane Furnace Error Codes

NOTE: If a flame is detected the control flashes the LED for 1/8 of a second and then enters a flame stabilization period. Where the flame is usually. If it has opened, check for proper combustion air, proper inducer operation, and primary heat exchanger failure or burner problem.

  1. Sign in Loading...
  2. That means the infuser (fan sound) will turn on and off three times.
  3. This could be caused by low gas pressure or faulty gas valve.
  4. Shane D is online now I have a Trane XL 80.
  5. The furnace will lock out for one hour and then restart. 9 RED FLASHES: Indicates reversed line voltage polarity or grounding problem.

These are York error codesYork Furnace error codes are seen in three colors, red, green, and amber/yellow. They are small round metal disc looking devices that have two wires attached to them and a little button on top of them. References Wico: Trane Furnace Error Codes Promoted By Zergnet Comments Please enable JavaScript to view the comments powered by Disqus. Trane Error Codes 126 Search these topics or contact your Trane Comfort Specialist for answers.

Lee Bevan says: October 24, 2015 at 8:28 pm David, an update on the XR80. Trane Xv95 Error Codes Check and clean filters, tighten wiring and check the flue for blockages.6. Error codes is flashing 4 times, which I believe is "Open High Temperature Limit Device." Furnace runs and circulates air, but no heat.What do I do to fix it?

Expert: M Oglesby replied5 years ago.

I didn't pay him yet wondering if the motor wasn't the problem? Trane Xv80 Red Light Flashing Decipher nine LED flashes to mean the high-stage pressure switch circuit will not close during a high-stage-induced draft blower operation. If the failure is internal to the control, the light will stay on continuously. Ask Your Own HVAC Question Customer: replied5 years ago.

Trane Xv95 Error Codes

The burner tray is where the burners are located. http://www.justanswer.com/hvac/2uygq-hi-ore-i-trane-xl80-flash-error-code-blows.html i have changed the batteries in the thermostate, I also shut it off from the breaker and back on to try and reset… Ken says: January 19, 2016 at 8:24 pm Trane Furnace Error Codes After the third time, the error code will flash. Trane Ac Error Codes The LED will flash “7” during this lockout.A Yellow LED labeled “FLAME” is provided to indicate flame statusFlame Status - When flame is sensed, the flame LED is lit.

The gas line comes in up above the compartment I can see when I remove the door panel.Customer: I thought you were her to assist me! http://u2commerce.com/error-codes/trane-furnace-error-messages.html JRESHOW 658,447 views 13:25 Trane XL-80 furnace malfunction - Duration: 12:53. How to Troubleshoot a Trane... Furnace blows hot air and does not shut off. Trane Xr80 Flashing Red Light Codes

But since they are updated often, your local Trane Comfort Specialist is the best source for the most appropriate version for your specific product. Check and clean flame sensor. It can be a full circuit error.Wow, who would have thought that my furnace could tell me so much!A series of 8 flashes means there is a low volt signal at this contact form Have your local temperatures been extreme lately?

If the limit switch is open and a call for heat is present, the control de-energizes the gas valve and runs the indoor blower motor on heat speed, and runs the Trane Furnace Red Light Flashing So right away, I knew it had to be something to do with the gas valve. Some models may have different different codes but these are common.

Recommended Action: Make sure your thermostat is on and set to heat.

Way to go Trane…morons!!!! Mine is acting up, and I don't know how to tell what is wrong with it.I am just the woman to help you with that Ray.You know that Trane furnace troubleshooting Related Searches You May Like How to Fix Trane Heating Furnace Problems How to Fix a Pressure Switch Error on a Trane How do I Troubleshoot Codes on a Carrier Furnace? Trane Xv95 Flashing Green John says: December 23, 2015 at 12:46 am I have trane 80.

Owners Support Maintenance Tips Air Conditioner Maintenance Gas Furnace Maintenance Tips Oil Furnaces Maintenance Tips Heat Pump Maintenance Geothermal Maintenance Tips Packaged System Maintenance Air Handlers Maintenance Ductless Systems Maintenance Tips All brand heaters and air conditioners. 22766799 Type Your HVAC Question Here... The control will do a soft lockout, but will still respond to open limit and flame. navigate here M Oglesby : The first that we will try to locate is the Main Limit Switch.

Anyway, I digress. Your indoor unit is running but the outdoor unit is not. demandmedia.com © 1999-2016 Demand Media, Inc. Nordyne M1M, N1B series error codes m1m_m1b_series_nordyne_error_codes.pngFile Size: 1166 kbFile Type: pngDownload File Nordyne G5RC error codes nordyne_g5rc_fault_codes.pdfFile Size: 1000 kbFile Type: pdfDownload File These are some common Trane

With this fault code the control will turn on both the inducer motor and supply air blower. Recommended Action: Check the following: Is your system cycling constantly? Credentials confirmed by a Fortune 500 verification firm. Ryan Wells 14,448 views 9:00 HVAC Maintenance: Trane XE 80 Heat- Edited Version - Duration: 11:58.

Steven says: March 11, 2016 at 3:33 am David Allred i have a trane xe-80… it starts up blows heat for 5 min. Good luck everyone, I am going to try all suggestions.