Home > Treadmill Error > Tunturi Treadmill Error Codes

Tunturi Treadmill Error Codes

Contents

An E1 code just means that the console is not getting a reading from the reed switch (Speed Sensor). Things You'll Need Allen wrench Socket and ratchet Voltage meter Screwdriver Related Searches THE LIVESTRONG.COM MyPlate Nutrition, Workouts & Tips GOAL Gain 2 pounds per week Gain 1.5 pounds per week Alatech treadmill controller 6690 error codes | Al... The problem could also be associated with a defective motor. check over here

Generated Sun, 30 Oct 2016 19:29:43 GMT by s_wx1194 (squid/3.5.20) Unplug any connections and replug. The pipe is marked with a decal. 2. Resistance is measured from black and white wires (see picture in 3rd page). http://www.lifespanfitness.com/fitness/resources/articles/what-does-your-treadmills-error-code-mean

Treadmill Error Code E1

If the error is still shown, turn the treadmill OFF and unplug from the wall outlet. The spare part list is at the back of this manual. Question about T30 Programmable Treadmill 2 Answers My tunturi T 20 gets ...tunturi T 20 gets error code E 7.

Co-authors: 6 Updated: Views:35,064 Quick Tips Related ArticlesHow to Repair a Corrupted Memory CardHow to Fix a Cyclic Redundancy Check ErrorHow to Fix a Keyboard That Has the Wrong CharactersHow to Depending on the model, it may be necessary to remove the hub covers on each side of the treadmill to access these bolts. If the display now works properly, replace the damaged wiring harness. Treadmill Error Code E3 Use of this web site constitutes acceptance of the LIVESTRONG.COM Terms of Use and Privacy Policy.

If this does not resolve the problem, remove the bottom hood cover and replace the wiring harness from the controller board to the base. 3 Deal with motor speed issues. Treadmill Error Code E2 By supporting the device on one of the side rails you can also vacuum it from below. To print the manual completely, please, download it. http://www.fixya.com/tags/tunturi_treadmill_error_code Turn the power switch off, wait 1 minute and turn the power switch on again.

We do not accept any responsibility or liability for the accuracy, content, completeness, legality, or reliability of the information contained on this website. Treadmill Error Code Problem Insufficient lubrication will cause the belt, running deck and motor to wear out and break. more weight on one foot). LOWER BOARD AND CONNECTION LOCATION Lift motor calibration The lift motor calibration is done manually by following the following steps:1.

Treadmill Error Code E2

Our shop is specialized in treadmills and stationary bikes spare parts, such as treadmill belts, drive belts, treadmill motors and controllers. Turn the power OFF, wait 5-seconds and turn back ON. Treadmill Error Code E1 Turn both adjustment screws an equal amount, ¼ turn clockwise. 3. E1 Error On Horizon Treadmill Any ideas?

Align the belt according to the following instructions: 1. http://u2commerce.com/treadmill-error/treadmill-error-codes-e3.html What does this mean please? His hobbies include horses, motorcycles, road racing and sport fishing. The device must under no circumstances be lubricated with silicone! Treadmill Error E6

  • NOTE!
  • Loosen the belt adjusting screws at the back of the treadmill, if necessary.
  • Wipe off the inside of the running belt using a harsh brush.
  • E7 The values the lift motor potentiometer is sending are not within the preset limits.
  • It is important to know when the E1 occurs and what was being done when it occurred.
  • Answer this question Flag as...

Official Partner of the LIVESTRONG Foundation FOOD FITNESS HEALTH TRACKER MORE WORKOUTS WEIGHT MANAGEMENT RECIPES DISEASES & CONDITIONS LIFESTYLE FASHION & BEAUTY PARENTING RELATIONSHIPS & FAMILY HOME Sports and Fitness Fitness EditRelated wikiHows How to Repair a Corrupted Memory Card How to Fix a Cyclic Redundancy Check Error How to Fix a Keyboard That Has the Wrong Characters How to Adjust Bass Tighten the screws (A) and verify correct elevation by measuring ERROR CODES E1 The error will appear if the upper board cannot receive pulses from the speed sensor for 10 seconds. http://u2commerce.com/treadmill-error/treadmill-error-codes-e7.html When problems develop with the sensor, the display panel might show an error code.

During the first 200 km of use, the running deck must be lubricated at intervals of 50 km. Treadmill Error Codes Manual Treadmill Lift motor potentiometer value table The values in the * Table 1 are reference information for troubleshooting only. The system returned: (22) Invalid argument The remote host or network may be down.

Find the cable that goes between the board under the motor cover and the console.

If the error is still shown, turn the treadmill OFF and unplug from the wall outlet. Answer this question Flag as... Do not use solvents. Trojan Treadmill E1 Error Works now and again, ...

Photo Credit Ancika/iStock/Getty Images The treadmill speed sensor records the revolutions per minute of the front roller and the computer converts this reading to miles per hour. If the problem persist call:206-881-7392 tunturi treadmill God bless ... Press ELEVATION DOWN to decrease the elevation to minimum percentage 0%Press SPEED UP to increase speed value and ‘SPEED DOWN' to decrease speed value. http://u2commerce.com/treadmill-error/treadmill-error-codes.html Check the stability of the sensor in the bracket that holds it to the motor.

NOTE! If the running deck is at a low position press the incline up button. From that point, the speed sensor can be fixed. Use an Allen wrench to remove the bolts that secure the motor cover at the front of the treadmill.

If the previous steps do not solve the problem, this is likely because the error is caused by a defective motor (too much current need from the motor causes the board What can I do? If the error code is still shown please contact customer service. Write an Article 121 Hello, !

Yes No Not Helpful 0 Helpful 9 Unanswered Questions How do I contact a repair company for a York treadmill in Australia? Posted by Parts for Treadmill at 19:38 Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest Labels: how to fix a treadmill No comments: Post a Comment Newer Post Older Post Home If the wires are properly connected and the error is still shown please contact customer service. in.

Your cache administrator is webmaster. O W N E R ' S M A N U A L ADJUSTING THE BELT TENSION The belt must be tensioned if it begins to slip on the rollers.